Search results

Search the forum Search Articles
  1. delong_1

    EFILive Tuning for Larger % Injectors

    Bumping this back up. I'm having a terrible time with this setup still. Still a bit of injector rattle, it wants to smoke all the time and egts are always high even when the turbos are lit
  2. delong_1

    Reputable diesel shop?

    what are you looking to get done?
  3. delong_1

    EFILive Tuning for Larger % Injectors

    thanks, i was just trying to get something figured out so i will be able to drive the truck. :baby:
  4. delong_1

    EFILive Tuning for Larger % Injectors

    Doing a little searching to try and figure out something. I have been having a tough time getting a base tune dialed in with my new setup, at idle it's smooth and quiet. Driving around 1600 rpms and above if I give more throttle to accelerate I'm getting some injector rattle. I have adjusted...
  5. delong_1

    Gear stuck on CP3

    i should have a spare gear as well if you cant get it off of the pump.
  6. delong_1

    new build

    drove it home last night and to work this morning. still have a quite a few things to finish but it finally runs right:happy2:
  7. delong_1

    Help: Odd oil leak....pouring!!!

    that is the same area that the little hole in the valley will drain, have you checked down there? i have had a few leaks that i had a hard time locating and they ended up coming from the valley.
  8. delong_1

    Ford went 9.49 @ 147

    stock rods, stock pistons with big valve reliefs, big cam, ported heads, etc. The still amazing part is the stock rods.
  9. delong_1

    new build

    as an update cam #2 is in, heads are back on, got quite a bit to reinstall.......:mad:
  10. delong_1

    Ford went 9.49 @ 147

    he did some testing last weekend was running 6.2's in the 1/8 spraying of course but he was also running 6.8's on fuel fwiw
  11. delong_1

    new build

    like the rest of the project, one step forward and two back. now im fighting rail pressure issues. thought the original was bad, took belt off and hooked up the reg and idled fine. swapped controllers worked alright now its doing it again, took belt off etc again but this time rail psi is...
  12. delong_1

    Intercooler Alternative to the Big Names

    x2 that was what i thought of. i got my banks without the piping for a really good price, several hundred less than any of the other coolers, i just didnt know if you could really sell them retail that way.
  13. delong_1

    new build

    Well haven't been gaining much ground in the past couple days. Overcame several issues like a blown heater core but it runs correctly now. Hopefully this weekend I will be able to put some miles on it
  14. delong_1

    Question: What size

    -6an on journal bearing, -4 for bb
  15. delong_1

    T4 pedestal measurments.

    i have a couple cast peds, i could send you either one so you could have exact measurements.
  16. delong_1

    The Build: 2001 ECSB Silverado 2500HD "SS"

    Congrats:thumb: i know the feeling, finally got mine running right last night.
  17. delong_1

    Help: motor issues

    ya, we finally got it figured out. will post details tomorrow after a couple phone calls.
  18. delong_1

    Help: motor issues

    compression is over 330ish already
  19. delong_1

    Help: motor issues

    fwiw there is zero blowby
  20. delong_1

    Help: motor issues

    been trying to get my motor going these past few days and im having no luck at all. it will start and run but not well. running rough, smoking black and has no throttle. I have tried about everything i can think of with no luck, tried spare ecm, ficm, different tunes, etc. pulled injectors...
Top Bottom