Search results

  1. delong_1

    Show off your new tools!!!

    well i just ordered a 68" epiq with the stainless top, ill post pics when it gets here:woott:
  2. delong_1

    Allison 5sp: trans whines

    thanks for the help today Mike, i will have to wait until tomorrow to see what happens. the only local place open today that had an internal filter was napa and they wanted $68.00 for one........
  3. delong_1

    Allison 5sp: trans whines

    Mike can i give you a call? if you would rather me not since it is Sunday after all i understand, i figured it would be faster than back and forth on here.
  4. delong_1

    Allison 5sp: trans whines

    i have the pump all torn apart at this point, the internal filter looks fine, anything under 300 psi there is no noise its just when it reaches 300 it makes the needle jump and the noise starts. the gaskets were new and they look fine dont see anything out of the ordinary, the valve is a modded...
  5. delong_1

    Allison 5sp: trans whines

    Is there any way to test for a leak from the filter port to the pump? If there is a leak it would have to be in the pump halves or the separator plate
  6. delong_1

    Allison 5sp: trans whines

    Honestly I just want good pressure to keep the trans alive, I don't really care what parts I use to get there. Fwiw
  7. delong_1

    Allison 5sp: trans whines

    300 psi, the pressure mods were the only changes from the last time. Mainline psi went from 240 max to 300 with the ats parts.
  8. delong_1

    Allison 5sp: trans whines

    guess i get to pull the trans again... filter was still fully seated when i dropped the pan.
  9. delong_1

    Allison 5sp: trans whines

    could it just be their new valve or the pressure, i guess thats what i need to figure out.
  10. delong_1

    Allison 5sp: trans whines

    surely the filter is in because i did check the pressure, i would assume if it was just sucking air it would do it all the time? or am i wrong thinking this?
  11. delong_1

    Allison 5sp: trans whines

    so i finally got my trans back together, while it was apart i changed some pressure mods from a shim to the ats spring and valve. now this trans whines anytime the pressure gets over a certain pressure, at that time the gauge needle gets erratic. at idle to about 1200 rpm all is normal. does...
  12. delong_1

    Denver area machine shop

    mtn high did mine, if not there is also ridge reamer in arvada
  13. delong_1

    New member from CO

    Welcome:thumb:
  14. delong_1

    Well I guess it's time

    250 then
  15. delong_1

    Well I guess it's time

    we only charge 200 to open the bowl, not that it matters
  16. delong_1

    Well I guess it's time

    you honestly sent the pistons off to have guy open the bowl? you know know any machine shop can do this and on the cheap, to each his own i guess. also if you need i can get one of my sets of heads refreshed if you cant find a set.
  17. delong_1

    Broken Crankshaft Count?

    Only if the guys that offer the cams know the firing order............ been down that road, no thanks
  18. delong_1

    New Dyno Numbers

    Congrats!!!!!!
  19. delong_1

    Stocker upgrade or ???

    you guys miss the drop in part...... how about the rcd modded stocker?
  20. delong_1

    LB7: dampers????

    mine only broke once. a handful of passes a full power, about 3000 total miles on the build and was usually run around a 700hp