Search results

Search the forum Search Articles
  1. ikeG

    Advice needed.

    We'd buy it the way it is Chris
  2. ikeG

    Hayden Fan Clutch

    Advance has a 'severe duty' that crosses part numbers with the 2886 for $69. Wondering if I should stick to a real Hayden or go Kennedy or what
  3. ikeG

    Hayden Fan Clutch

    But the Hayden and Kennedy ones promise to be better as far as engaging earlier etc? Sent from my XT1585 using Tapatalk
  4. ikeG

    Hayden Fan Clutch

    Which one should I buy for a 260k farm beater lly that's constantly towing skid loader etc?
  5. ikeG

    Does anyone know if there is/are any other types of custom tuning in the works?

    Trade your lmm for a lbz or older. Problem fixed. Better yet, switch to bosch standalone
  6. ikeG

    Making trans cooler lines

    Dhd fittings and hydraulic shop hoses Sent from my XT1585 using Tapatalk
  7. ikeG

    Making trans cooler lines

    Heres a link to the fittings I used. http://dirtyhookerdiesel.com/c-932403-transmission-hard-parts.html Sent from my XT1585 using Tapatalk
  8. ikeG

    Making trans cooler lines

    I used dhd's threaded fittings for the trans and cooler and then had hydraulic lines made to my liking to relocate the cooler on our puller
  9. ikeG

    Making trans cooler lines

    I always wandered about this. Thanks for the info. I've seen people use heater hose and work gear clamps, so I didn't think the cooler lines had stupid hi psi
  10. ikeG

    1055/ goerend k

    The 1055 works well with any s400 with the 87 tw and smaller, provided you stay 1.10 a/r or tighter. Sent from my XT1585 using Tapatalk
  11. ikeG

    LMM: Seem to be loosing fuel prime

    Fix the prime issue before installing a lift pump, because the pump will mask that issue
    • ikeG
    • Post #5
    • Forum: LMM
  12. ikeG

    1055/ goerend k

    A 1055 is the jack of all trades from my experience, until you get into pretty seriously big stuff. That said, I've appreciated goerends customer service the past couple seasons. I've ran an R, but was a modded stock turbo. So it wasn't really pushed Sent from my XT1585 using Tapatalk
  13. ikeG

    1055/ goerend k

    We use a 'Q'. Stalls higher than a 1053-1, couples as good as you could expect
  14. ikeG

    Transfer case gasket

    Thanks mike Sent from my XT1585 using Tapatalk
  15. ikeG

    Transfer case gasket

    Why are some aftermarket gaskets solid? Is there a need to stick with the one that only has the gasket material where the the two surfaces meet, instead of solid?
  16. ikeG

    Rail pressure sensor

    I am not able to upload a log file?
  17. ikeG

    Rail pressure sensor

    I'll attach a log tonight Sent from my XT1585 using Tapatalk
  18. ikeG

    Rail pressure sensor

    Yes. Only change in log when it happens is the rpm dying​ off
  19. ikeG

    Rail pressure sensor

    It would run fine in the upper 28xxx's iirc, which is 195-197mpa. So not like it's low or anything. I'd be interested to know the cutoff​point catman. Assuming you can just make more & more. What ECM? LLY? Sent from my XT1585 using Tapatalk
  20. ikeG

    Duramax fuel line replacement

    You have the feed & return switched Sent from my XT1585 using Tapatalk
Top Bottom