Search results

Search the forum Search Articles
  1. Harbin_22

    Danville 68stg2r

    We drove from Phoenix to Flagstaff and I swear we were driving up hill for 3 hours straight lol
  2. Harbin_22

    Lml: Ez lynk vs efi live

    ..
  3. Harbin_22

    Lmm aftermarket guages...

    I don't use the app and photobucket would t let me post picks anymore. PM a number and I can send some to you.
  4. Harbin_22

    Lmm aftermarket guages...

    I have the autometer steering column pod. Actually fit well and looks nice. I have two other gauges that I mounted in my center console that turned out nice.
  5. Harbin_22

    Allison builder recommending dex 3

    That's what I used last time because it was all the parts store had 6 gals of lol. Working fine.
  6. Harbin_22

    LMM Transmission Issues

    Nope. LMM A50 and A40 can be swapped either direction. Mine was an A50 ,not tunable at the time, put into an 07.5. The 07.5 A40 was put in my truck to tune it. Both ran fine with zero issues They were not flashed over, obviously couldn't flash the A50 at the time, and worked fine. My 2010...
  7. Harbin_22

    LMM Transmission Issues

    Any LMM TCM can be swapped. My 2010 is using an 07.5. No reprogramming needed. I did do a relearn since I had a built trans and this one came out of a stock truck.
  8. Harbin_22

    lifting heads?

    What engine?
  9. Harbin_22

    LMM Transmission Issues

    If you get any TCM out of another LMM truck, you can directly swap them, no programming needed
  10. Harbin_22

    Waglers New Budget Rods

    I cracked 4 delipped LB7's right at 1,000 with 68/483 twins. Made it maybe 5k miles lol. Along with a brand new LB7 crank.
  11. Harbin_22

    Little Drive Line Angle Help Please

    Yeah I have bars on all the time. Thanks for all the help to a small problem I was making out to be bigger lol.
  12. Harbin_22

    Little Drive Line Angle Help Please

    Okay, went out and double checked, feel like a dummy but the diff is pointed up already. So is my problem the drive shaft and joints are too straight? The diff is either 3-4°, the drive shaft is 4-5°, and output is 5-6°.
  13. Harbin_22

    Little Drive Line Angle Help Please

    You would know the shims I was looking at were 2,4,6,8° lol. Wonder how much shim in the trans mount it will take to get it up 5°
  14. Harbin_22

    Little Drive Line Angle Help Please

    Mine is definitely not low enough for that to happen, I hope lol. I'm going to double check my measurements tomorrow and order a few shims and see what happens.
  15. Harbin_22

    Little Drive Line Angle Help Please

    Have you checked your angles? Mine has a weird vibration around 50-60mph. Doesn't seem to always do it, but it isn't 100% smooth above 60 either. I hope this is the cause
  16. Harbin_22

    Little Drive Line Angle Help Please

    Anyone know the best place to get a steel 5° wedge for the rear end Edit: I found some.
  17. Harbin_22

    Little Drive Line Angle Help Please

    Do you think the output yoke needs to come up a couple degrees? Or do.you think rotating the diff will change the angle of the drive shaft enough to make it okay? If all of them are at 5°, that puts me at 0° working angle and everyone says that's bad.
  18. Harbin_22

    Little Drive Line Angle Help Please

    I guess if I bring it up, that will change the driveshaft angle some to, everything I read said you don't want all of it to equal 0
  19. Harbin_22

    Little Drive Line Angle Help Please

    Need a little help figuring out of my angles are right or not. I've been chasing an odd vibration and wondering if the angles are causing it. Truck has 3" lowering shackles, overloads removed, and Tbars let all the way down. Hope I can explain this well enough... Okay, at ride height on...
  20. Harbin_22

    Cracked Piston

    No it's not mine, sorry I worded that a little wrong lol.
Top Bottom