Search results

  1. DPC

    Af cam wiring?

    Thanks.:thumb:
  2. DPC

    Af cam wiring?

    LB7/LLY guys are you actually pulling the pins on the FICM connector or are you cutting and splicing the wires about 2 inches up the connector harness? I took apart the connector and it does not look like the pins will pull out, thanks.
  3. DPC

    Af cam wiring?

    Bought it from So Cal and yes they know its a LB7.
  4. DPC

    Af cam wiring?

    Will this set codes like P1223 and P1232 Fuel injector open circuit? Causes a rough idle. I have checket the entire harness from the ECM to the injectors with a DMM and no open circuits or shorts. I have switched out FICM, swapped injectors, checked valves, and compression and still have the...
  5. DPC

    LB7: So I'm currently working up a build with SoCal.

    Here is one, had it on high idle to warm it up. http://youtu.be/3zWj8AUjfao
  6. DPC

    Allison Trans-Brake

    Sled pullers with a trans brake?? NOT that sled pullers would cheat...:roflmao:
  7. DPC

    Coilovers!!

    Did you end up putting these on? I was looking at the same setup and was interested on how it worked out, thanks.
  8. DPC

    Balance rates issue

    Do you have any codes? P0300 misfire and the P1223 open circuit codes? You can have these codes without a cel.
  9. DPC

    16x10 with 6" backspace?

    4.5 backspace I assume? How bad do they rub in the front?
  10. DPC

    Paint delamination

    The hood on my 03 is pretty bad, bought the truck new in AZ.
  11. DPC

    LMM: Wisco Pistons

    I thought the OP was talking about fuel knock, not engine noise?? Fuel knock, from what I have seen, has its own very distinct sound and sounds nothing like piston slap or engine noise??
  12. DPC

    16x10 with 6" backspace?

    Much cheaper than Real, they look to be about 10lbs a wheel heavier with steel. You are correct about the real wheels, not DOT approved.
  13. DPC

    16x10 with 6" backspace?

    I checked with real wheels, they will make them for 280 each. Sent from my iPhone using Tapatalk
  14. DPC

    16x10 with 6" backspace?

    I have been looking for a 16x10 aluminum wheel with 6 inches of backspacing, does such a wheel exist without going custom? Thanks for your time.
  15. DPC

    What kind of fitting in exhaust manifold for drive pressure?

    I have used both mechanical and electric style drive psi gauges. The electric sending units seem to hold up much better to the soot, don't plug up. I used aluminum coil from a $9.00 choke kit through napa. I have used this setup for a year plus on the dodge with no issues.
  16. DPC

    Transmission options

    I could always start with a manual VB and if it does not work out I know there are plenty of 5.9 guys who would buy the manual setup.
  17. DPC

    Transmission options

    I have seen a manual VB setup on a 47RE with reverse shift pattern and two switches, one for converter lockup and one for OD, no PCS. Can this be shifted fast enough? Any advantage to using an air shifter +PCS over just the PCS?
  18. DPC

    Transmission options

    Wow, very impressive shifting! I will send you an email to pick your brain about a few things on your setup. Thanks to everyone for all the information.
  19. DPC

    Transmission options

    I think he is running a rossler/nc 400 or something like that.
  20. DPC

    Transmission options

    Pretty sure he switched to a different tranny to get him into the 8s.