Search results

Search the forum Search Articles
  1. DPC

    Colorado 6L50 line psi

    Time to back it down then it has the weird downshift clunks...What kind of torque can these hold? This 2.8l is very torquey with tuning. The converter feels like it has a partial lockup (or its slipping) when I roll into the power in the higher gears. On the scanner I can watch it slip then...
  2. DPC

    Colorado 6L50 line psi

    No 6L50 gurus on here?
  3. DPC

    Colorado 6L50 line psi

    I've been messing around with my 17 Colorado. How much line psi can these handle without causing problems on a stock transmission? The line psi table by RPM/Gear in EFI live shows 105. The max line PSI table shows 275 with a max clutch psi of 218 and a max PCA of 110. I was able to...
  4. DPC

    DK Engine Parts

    I put a set on an 01 about 5 months ago and everything fit as it should. Long term, have no idea.
  5. DPC

    LML trans pressure boxes

    Thanks for the input, that makes things much easier and cheaper.
  6. DPC

    LML trans pressure boxes

    Any input on pressure boxes for the 2016 Allison? I see BD and ATS make one and wanted to see if they are any better then the G-solenoid mod. I've already done the solenoid mod and now have a transmission tore down with smoked C1 clutches. After building it I was thinking of adding a...
  7. DPC

    Post CP3 swap - won't stay running p0087

    Who's CP3 conversion kit did you use? Did you leave the injector return regulator in? Those injectors will return too much fuel without it.
    • DPC
    • Post #12
    • Forum: LML
  8. DPC

    Chevrolet cruze diesel

    2014 Cruze I bought a 2014 about 6 months ago that had 27K on it. The fuel milage is wonderful. I did have some issues with the DEF heater but turned it off with EFILive and its been trouble free for about 10k miles now. Car still regens just no DEF.
  9. DPC

    Lml efi live HELP!!!!

    Have you checked the basics, software updated, bootlock updated? What are you flashing with, autocal or V2?
  10. DPC

    Need some help on Piston Protrusion

    The "D" gasket is .010 thicker then the "C" gasket. http://dirtyhookerdiesel.com/i-18480594-gm-97358465-oem-right-side-grade-d-head-gasket-010-thicker.html
  11. DPC

    Fiberglass hoods

    I found this place awhile back http://gtsfiberglass.com/ They charge around $1400 for a front clip and bumper which would probably be the route to go, just not sure if I want to tear the entire front end off...would make it easier to work on.
    • DPC
    • Post #8
    • Forum: LB7
  12. DPC

    Fiberglass hoods

    Yes, 03-04.5 cat eye. I have also checked into front clips but can only find the pre-runner style, talk about expensive!
    • DPC
    • Post #6
    • Forum: LB7
  13. DPC

    Fiberglass hoods

    It is a Chevy and a drag truck.
    • DPC
    • Post #4
    • Forum: LB7
  14. DPC

    Fiberglass hoods

    I am looking for a link to a cheap fiberglass hood. The hood is going to be cut for a hood stack and waste gate, it will also get pinned. The only thing I can find when searching are the expensive cowl induction type hoods. Thanks for your time.
    • DPC
    • Thread
    • Replies: 7
    • Forum: LB7
  15. DPC

    LBZ 73 Nova

    Dry or wet heads?
  16. DPC

    6" bellmouth/turbo horn intake

    Thanks!
  17. DPC

    6" bellmouth/turbo horn intake

    Does someone make a 6" bellmouth/turbo horn inlet? 5" is the biggest I have been able to find, thanks.
  18. DPC

    Duramax wire tuck

    Makes changing injectors not so bad (for an LB7). Looks good.
  19. DPC

    Help! Piston Ring setup

    Here is a pic from the service manual. The "4th" ring is the spring inside of the bottom oil ring. Sent from my iPhone using Tapatalk
    • DPC
    • Post #7
    • Forum: LB7
  20. DPC

    Dropping rail with 3 CP3s?

    240mpa! That's about 35K correct?!
    • DPC
    • Post #46
    • Forum: LB7
Top Bottom