Search results
-
WIX oil filters for a buck?
Crap, I better stop by tomorrow and grab em before the management finds out!- Ridin'GMC
- Post #26
- Forum: Fluids and Maintenance
-
-
Help: Any Massachusetts Cops on the forum???
Just wow. If a police pulls you over, that means you did something wrong or something is wrong with your vehicle without your knowledge. It's their job to make sure everything is in ordinance for yours and everyone's safety. If you're one of those F*** the police guys, you're an idiot and you...- Ridin'GMC
- Post #59
- Forum: Smoke Signals
-
Help: Any Massachusetts Cops on the forum???
I've never heard of such thing as driving with no plate and not getting in trouble. Mass is somewhat strict on certain things. You have 7 days to get an inspection sticker. License plates are needed the day you purchase the vehicle to drive. If your truck has a lift or dark window tints, you'll...- Ridin'GMC
- Post #44
- Forum: Smoke Signals
-
Got my trans built but shifts extremely hard
Aluminum won't stick to the magnet. The picture doesn't really show close enough what the debris is. At some point, some of the debris looks close enough to be aluminum shavings but I could be wrong.- Ridin'GMC
- Post #135
- Forum: Mike L's Trans Talk
-
Got my trans built but shifts extremely hard
Any metal shavings is not good. I'm not exactly sure what those are from. You'll have to wait for what Mike or Evan instructs you to do next.- Ridin'GMC
- Post #133
- Forum: Mike L's Trans Talk
-
Got my trans built but shifts extremely hard
Did you take the pump apart to make sure everything is okay or you just left it alone and put the boost valve in? Evan, it's possible that the filter could be plugged up from lint from the rags? That if he used cloth rags to wipe everything off.- Ridin'GMC
- Post #80
- Forum: Mike L's Trans Talk
-
Got my trans built but shifts extremely hard
There's a good chance you messed up something in the pump. Before driving out, you should always check the transmission pump pressure. Low pressure will cause slippage, sometimes sloppy shifting. You may have set the clutch clearances right but I believe your pump isn't up to spec. You probably...- Ridin'GMC
- Post #72
- Forum: Mike L's Trans Talk
-
-
Inspection in Ma.
If you get caught by the environmental police, you will get a big fine for running no dpf or cat. But if you gut it and leave the housing intact, they can't prove its been gutted. I wouldn't worry about it, you won't see the environmental police around here. I've never seen one or heard anyone... -
Inspection in Ma.
You probably can get away with gutting out the dpf and cat while leaving the housing intact. Just make sure it looks like a factory setup, don't cut up any of the pipes. As long it passes the opacity test and no CEL, you should be okay I think. -
LLY: Intercooler pipes question
You won't notice any power gains with your setup. The only time you will notice is pushing alot of air with large chargers. -
Inspection in Ma.
It is getting there. MA and CA are the top 2 state for strict emission laws. The problem with MA for vehicle inspection is they are not just focusing on the emissions like AZ does. They go over the entire vehicle by checking front end, suspension, aftermarket performance parts, and safety... -
Inspection in Ma.
If you know someone who would pass you with no emissions, go to that person instead. But be careful. MA is cracking down on inspection stations for passing vehicles with no emissions or illegal tints, too high of a lift, etc. It took me over a year to find someone to pass mine. State police does... -
loping after fass 95 install and injectors
LB7 do not like high lift pump pressure, it causes them to lope any higher than 10 psi. The LBZ can run at 14 psi without any lope issues. -
Rear axle shaft
Are they really any stronger than the stock application in the 30 spline? I see that they have one rated for my tire size, though I've never heard of anyone breaking one just from playing around besides pulling competitions. -
Rear axle shaft
I've been battling rear hub seal leaking on the driver's side. Got annoyed with it and ripped out my axle shaft at work and put it on lathe. Found out my driver's side axle shaft is bent after trying to get to the root of the vibration at highway speed. My question is, should I stick with stock... -
Dropped The Truck Off at HSP Yesterday!
Very pretty! I hope you have a 5 point harness, that thing is going to throw you all over the place- Ridin'GMC
- Post #29
- Forum: HSP Diesel
-
LB7: built front end mods?
This sounds like a suspension issue. I have the kryptonite and never had any issues with it, my current tire is about to hit the 50k mark with kryptonite steering, even my last tire lasted that long too. The only time I get outer tire wear is when I take corners like a race car or not rotating...- Ridin'GMC
- Post #12
- Forum: Drag Racing
-
Need help for choice of lift kit
Get a 6" and lower it to a 4". Ride quality will be much better. For a lift company, there are many good ones such as cognito, CST, zone, RCD....- Ridin'GMC
- Post #2
- Forum: Chassis, Suspension & Brakes