Search results

Search the forum Search Articles
  1. S

    Dyno Day this Sunday June 9th New Milford, CT

    It's going to be mass diesels dynojet
  2. S

    Dyno Day this Sunday June 9th New Milford, CT

    Gonna be ready for the stampede?
  3. S

    Dyno Day this Sunday June 9th New Milford, CT

    I still need a tcm tune for my puller :thumb:
  4. S

    Dyno Day this Sunday June 9th New Milford, CT

    One of my friends is putting it on. There will be 1st-3rd place HP trophies for both gas and diesel Also a burnout contest
  5. S

    Dyno Day this Sunday June 9th New Milford, CT

    There will be a diesel dyno day this Sunday in CT behind the New Milford Monro Muffler. I believe it's mass diesels dynojet Located at 150 Danbury Rd New Milford, CT 06776 Starts at 9:00 am Also they will be raffling off a LAUNCH scantool
  6. S

    Anyone with cognito uca replacment as part of leveling kit

    You will need longer front shocks or extended front shock mounts. Also if your torsion bars are cranked all the way and you need to go higher you will have to install leveling keys.
  7. S

    Off Season Sled Pulling Mods

    Looks good :thumb:
  8. S

    Northeast Performance Diesel Truck Pull/Dyno

    I think I went to Numidia last year :shots: :ralph: :alcoholic: :rofl:
  9. S

    Allison 5sp: having another issue on pulling truck.

    I'm running a converter with a 3000 rpm stall
  10. S

    Allison 5sp: having another issue on pulling truck.

    You can leave the line at 30-35psi? Teach me your ways :hug: I'm lucky to leave at 12psi @ 1200-1300 degrees when I leave
  11. S

    My girl Allison is starting to let me down

    I might have to make the trip up there Tim
  12. S

    My girl Allison is starting to let me down

    That would work if I had efilive :hug:
  13. S

    My girl Allison is starting to let me down

    Ok I'll check out the sensors. I wish I had a tech2 or something that was capable of reading the sensors.
  14. S

    My girl Allison is starting to let me down

    Check engine light too or just codes? Speed sensors? Input/output or wheel speed? How can the t-case cause shifting issues? Thanks Jesse
  15. S

    My girl Allison is starting to let me down

    My external filter probably has less than 20 hooks on it with 0 street miles and the tranny fluid probably has under 10 hooks on it. I've changed the fluid 3 times in the last 20-30 hooks and all 3 times the fluid was cherry red. Ill swap the filter and cut the old 1 open to check for debris...
  16. S

    My girl Allison is starting to let me down

    It has 2 brand new airdogs with about 10 hooks on them and no oem filter.
  17. S

    My girl Allison is starting to let me down

    This is in my 02 puller. Usually it will shift to 3rd gear in 15-30' depending on the track conditions but the last 2 pulls it hung in 2nd gear bouncing off the rev limiter till about the 200' mark before it finally shifted. Any ideas on what to check, change, or look for would be greatly...
  18. S

    Yokes

    The yokes merchant sells are oem GM yokes.
  19. S

    Yokes

    I went with a GM 1480 yoke on my dd/workstock puller and never had any problems. Just make sure to use new straps and bolts and you should also replace them every time you pull the driveshaft out. I haven't decided which one i'm going with on my puller yet though. I'll probably go with the...
  20. S

    Need help finding a v-band setup

    Let me know what you think from the pics
Top Bottom