Search results

Search the forum Search Articles
  1. fl0w3n

    Swapping Passenger Manual Seat for Full Power/Heated/Lumbar

    I'm unsure of where C399 goes to after, but I think it ties into C305 for the passenger side. Am I correct to assume I would be tie'ing these wires into C305 since they show they are the same circuit? If so, I don't know where the other remaining wires go. C305 driver on the left, C399...
  2. fl0w3n

    Swapping Passenger Manual Seat for Full Power/Heated/Lumbar

    I was muddying up my own thread so I wanted to start a dedicated one, hopefully I can sort the answer out here and people looking to do the same swap in the future can search and find this instead. Basically it's just capturing my thinking out loud, hoping for input from the wizards here, and...
  3. fl0w3n

    Pulling Dash - Anything I'm Missing?

    I'm also confused because I can't find connector details about where C399 goes to. Is it going straight to the BCM like I highlighted? Edit: I think I answered my own question, it's not going straight to BCM because I don't see anything about it in the BCM.
  4. fl0w3n

    Pulling Dash - Anything I'm Missing?

    Okay I got lucky and the guy who was selling the seats cut them out on the body side of the harness, so I at least have the connector to go into the passenger seat. I am looking at C399, but what's weird to me is it doesn't fully match what All Data is telling me. Is this common because of...
  5. fl0w3n

    Hazing LB7 - Couple of Injector Questions

    Where are you located? Have you tried calling the dealer to search for the cleaner? I was able to buy the last few bottles in Northern California or even the state maybe and they shipped it to me. It didn’t really wind up helping much though.
  6. fl0w3n

    Hazing LB7 - Couple of Injector Questions

    I was about to say the same thing, you’re going to have to crack all 4 high pressure lines and if they weren’t sealed up there’s a good chance you just clog up the remaining 3 injectors. there’s a possibility the dealership just tried to clean the high pressure lines instead of replacing them...
  7. fl0w3n

    Pulling Dash - Anything I'm Missing?

    Well, this whole project just got even more involved. I just picked up fully loaded seats (both power/heated/lumbar/memory) and a center console, plus the door panels. so looks like I’ll have the entire cab gutted, because at that point I might as well pull the carpet and pressure wash it out...
  8. fl0w3n

    Pulling Dash - Anything I'm Missing?

    Dang, I assume you're getting it at a discount because of your shop? I wound up getting one blend door actuator from the dealer and it was hundreds of dollars for an AC Delco one, I want to say something like $340. Rockauto has AC Delco for less than $100. Hard to swallow, but I do like using...
  9. fl0w3n

    Pulling Dash - Anything I'm Missing?

    It’s the 04 I plan on doing it to, and another good point on adding the filter. I guess I can inspect the heater core and just clean it out, I’d just hate to take it all apart and see that it is indeed bad and then be sitting around waiting for a replacement. @Bdsankey which blend doors were...
  10. fl0w3n

    Starts runs like sheet then dies

    Wait so the problem the whole time was an egr? I’m not following your last few posts
  11. fl0w3n

    Pulling Dash - Anything I'm Missing?

    If it's a commonly reported issue, I'll go deeeep haha. Looks like the shift cable is $100? Do they stretch out or just break? My cluster looks like it was already repaired by the PO so that should be good. Good points on everything else, a little elbow grease and consumables should go a...
  12. fl0w3n

    Pulling Dash - Anything I'm Missing?

    I plan to eventually pull my full dash apart to fix a few things that have been getting on my nerves. Since it's a pretty big task and I don't want to do it more than once, I just want to double check if there's anything I might be missing that I should look at while I'm there. It's going to...
  13. fl0w3n

    Anyone “overland” ?

    Nice! I've always wanted to do something similar to what you did with the front bumper, and I feel like the GMC's are just built for it with the steel top.
  14. fl0w3n

    Happy Thanksgiving!

    Happy thanksgiving and hopefully afterwards everyone can score some good deals on stuff they’ve been wanting!
  15. fl0w3n

    Illegal Tampering by Diesel Pickup Owners Is Worsening Pollution, E.P.A. Says

    definitely, it just sucks that it’s being promoted in mainstream media and the naive general population has zero interest in doing their homework on it. Meanwhile it’s making it harder and harder for the aftermarket to exist. When it comes time to vote on “it”, their ignorance can easily pass a...
  16. fl0w3n

    LB7: 02 LB7 Audio Overhaul

    I’m not sure why you’re saying that when the link you just posted is exactly what I said, just in detailed write up form.
  17. fl0w3n

    Illegal Tampering by Diesel Pickup Owners Is Worsening Pollution, E.P.A. Says

    Don't know if any one reads the NYT, but this article seemed relevant. Obviously nothing new, but pretty big bummer to see in such prominent form. https://www.nytimes.com/2020/11/25/climate/diesel-trucks-air-pollution.html
  18. fl0w3n

    263XHD transfer case stand alone solution?

    I’d check with TransferCase Express. My case was different but I swapped a NP271 into my truck and they were awesome to work with. Very knowledgeable
  19. fl0w3n

    Work truck

    Cool to see the life of a work truck chronicled like that hope the 6.6 works out well for you what industry/line of work are you in?
  20. fl0w3n

    Hummer H2 Dmax engine swap?

    Rode in one probably 12+ years ago, it was fun. So at least I know it’s possible, but know nothing other than that.
Top Bottom