Search results
-
-
LBZ, LMM MAF??
Does this look like something that would work? FEATURES: Used To Create A Custom Air Intake Polished Aluminum Body With ABS Components Tuning Components Are ABS Construction The Spectre 4 inch Aluminum Mass Air Flow Sensor Adapter Kit is designed for use with drop-in style mass air flow...- Mogman
- Post #7
- Forum: Duramax Hard Parts
-
LBZ, LMM MAF??
Thanks guys, maybe I will take a look at the donor intake pipe again or look for some 4" tubing to weld that piece in- Mogman
- Post #6
- Forum: Duramax Hard Parts
-
LBZ, LMM MAF??
Thanks to all that have helped me with this project, this forum is a great resource. So we are getting down to the minor details, the donor LMM had an aftermarket intake which I cannot use, so the question now is what MAF sensor I can use. I am using a LBZ intake horn and am told that it is a...- Mogman
- Thread
- Replies: 6
- Forum: Duramax Hard Parts
-
LMM heater hose options??
Thanks, I already ordered a plug, and I have located an o ring. -
-
2008 LMM dual alternator idler
It looks like I need to get an idler pulley to install dual alternators, I am assuming it is the same part number as the other two idler pulleys yes? The picture says 2006 but this still looks right, I have a K061369 belt to install. -
LMM heater hose options??
Thanks, I will check it out, I have plenty to do without making mid-stream upgrades. -
LMM heater hose options??
What do I do with the factory connection by the oil cooler? -
LMM heater hose options??
Well the hose goes over/behind the turbo and that has to go, (re-routed in front of the turbo would be the best solution) I just need to know if anyone makes an aftermarket fitting or if I have to brew my own, it is all one piece from the factory -
LMM heater hose options??
So the original heater hose that comes off of the left rear of the engine must be changed as it interferes with the doghouse cover on my HMMWV as it goes past the turbo, so I am wondering if there are any aftermarket connectors available or am I going to have to home brew something, Also I was... -
-
Alternator lead?
I cannot find this pigtail, anyone have a source for these? Actually I cannot find the connector on my harness, according to the manual I have there should only be two wires going to it, a brown and a grey, if I could find it I can simply cut it off and wire directly to an aftermarket pigtail... -
LMM lift pump?? DSP 5??
I see in the schematics there is a fuel lift pump control pin on the LMM ECM, I will be running an AirDog and wonder if this can be programmed to control the pump, I have not looked but assume the pin/lead is not even populated in the ECM connector but that could be remedied, I thought I saw...- Mogman
- Thread
- Replies: 1
- Forum: Duramax Tuning, Logging, and Gauges
-
Lower profile oil fill tube
Which direction does the van thermostat housing point the upper rad. hose? what is the part# (to fit 08 LMM)and can you recommend where it can be drilled and tapped for a 1/8" sending unit, I had intended to look at the forward facing threaded hole in the lower thermostat housing but it looks... -
-
Lower profile oil fill tube
I need to lower the oil fill tube on my 08 LMM, I am looking at a 01-05 tube that looks shorter, does anyone have a clue if this can be made to fit. I could cut down and weld up my original but this would look cleaner. Thanks -
-
Alternator lead?
On my 2008 LMM I cannot find a lead on the engine harness that fits the alternator (2 pin) is there a short pigtail that plugs into the harness? -
LYY intake horn on LMM turbo?
The S&B LLY intake horn came in yesterday and fits the LMM (without EGR) perfectly