What did you do at work today?

DefiantArms

Limp Mode Cowboy
Jan 28, 2016
897
1
18
St. Augustine, FL
I've got a nice starrett thread deapth gauge i picked up at auction that is ancient got 2 Kurt 8" cnc style vises at same auction for 75$ wooot Love auctions
 

malibu795

misspeelleerr
Apr 28, 2007
8,241
550
113
42
in the buckeye state
Last load for the week
14225431_10209481019075947_1967742980628889319_n.jpg



Looks colorful jeese
 

malibu795

misspeelleerr
Apr 28, 2007
8,241
550
113
42
in the buckeye state
Working on my Burb.
New rear rotors and pads
14224886_10209488935433851_657300762149342011_n.jpg

Front wheel fitment and measurements
14330105_10209489911698257_1367170724353941651_n.jpg

315/70/17 on 17*9 5"bs
14333195_10209491362494526_9117297098321564951_n.jpg

305/50/20 20*10 5"bs
14322459_10209491362214519_2667130378170895484_n.jpg


Need a 16/17*8" wide with 6" bs or a 17*9" with 7" bs
Means custom rims.. :baby:
 

six5creed

Member
Jan 6, 2016
1,046
58
48
N.C.
Got these 3 chainsaws running. Went to buy a bed from a lady on Saturday and wound up buying these 3 saws and a truck. 1993 GMC Sonoma V6 4WD, automatic, A/C etc with 131K miles. Gonna be my new DD as soon as I get it cleaned up and insured/tagged. They all been sitting for 3 years since her husband passed away. Put a battery in the truck and 5 gallons of fresh gas and drove it home. The saws just put new gas in them and they all run great.
 

Dozerboy

Well-known member
Jun 23, 2009
4,892
470
83
TX of course
Doing a little project at BPs HQ. Had to do a safety stand down Because we got out a hammer and that wasn't in our TSA...


Sent from my iPhone using Tapatalk
 

07keo02

New member
Oct 5, 2011
399
0
0
Phoenix, AZ
Wet sanded a few blades today sent the helicopters off to get painted and they didn't tape the blades was overspray all over them.

What do you do with heli's? I work on 206's in the medivac industry. Went in today for a daily inspection and they were taking off for a scene flight. Nothing else to do so went home, still paid for 8. Love the job. On call 24/5 but a more than fair trade off. Will head back to the base later for the inspection.
 

DefiantArms

Limp Mode Cowboy
Jan 28, 2016
897
1
18
St. Augustine, FL
What do you do with heli's? I work on 206's in the medivac industry. Went in today for a daily inspection and they were taking off for a scene flight. Nothing else to do so went home, still paid for 8. Love the job. On call 24/5 but a more than fair trade off. Will head back to the base later for the inspection.

Crew when needed /A&P mostly though i do same thing sit around all day wait for them to get back do the daily than go home did a 25hr today have a 300hr coming up with lots of tbo goodies :( working on 212's in Afghanistan pm me if you're looking for work and have A&P we're looking :thumb:
 

malibu795

misspeelleerr
Apr 28, 2007
8,241
550
113
42
in the buckeye state
Maintenance on the lmm.
Oil change, transmission spin on change new wipers, grease front suspension, topped off transmission fluid.
Found air compressor died, well doesn't pump air..
Something about a piston ring...
14344181_10209554610595689_1579907950784793935_n.jpg

14333698_10209555131728717_2247390597139355662_n.jpg

Happen to still have first one I bought too.. both are 33gl 150psi one has a 1.6hp other has 2hp motor. Plumbing both together, and upped discharge line/port from 1/4npt to 3/8npt. Did it on the newer one..also bumped to 1/2"hose as well.
Going to wire both to a 240v plug, since it has 2 120v legs one for each motor and they will share common ground.
Going to run a 1/2" cross over pipe for now like 5/8" or bigger but pointless when the discharge ports are smaller
14355093_10209555127968623_8700005824519655903_n.jpg

Running 3/8" quick connects and 1/2" line makes a big difference in Impact tool out puts
Vs 1/4" quick connects and 3/8" line... There is definitely an increase in performance from 1/4" to 3/8" quick connects as well
 
Last edited: