Twins with Twins, Anyone?

kidturbo

kidturbo

Piston Tester
Jul 21, 2010
2,539
1,377
113
Somewhere On The Ohio
www.marinemods.us
Definitely not your typical boats.. Gas powered boats are far easier and cheaper to work on... lol

We'll 12hrs later, back at it, ACME version 1 rear adapter hardware is out, and the trusty old dyno flywheel setup bolted on. Tomorrow we'll bolt up that new rear engine plate above, and hopefully be spinning a little higher R's this time.
 
NC-smokinlmm

NC-smokinlmm

<<<Future tuna killer
May 29, 2011
5,203
363
83
At Da Beach
kidturbo said:
Definitely not your typical boats.. Gas powered boats are far easier and cheaper to work on... lol

We'll 12hrs later, back at it, ACME version 1 rear adapter hardware is out, and the trusty old dyno flywheel setup bolted on. Tomorrow we'll bolt up that new rear engine plate above, and hopefully be spinning a little higher R's this time.
Click to expand...

I was referring to their propensity to be a tad difficult from time to time...:hug:
 
1FastBrick

1FastBrick

Well-known member
Dec 1, 2016
2,542
1,069
113
Junkyard
kidturbo said:
There was once a time Josh that I didn't. So I just quit playing. But now I look at it as Adam from Mythbusters says, "failure is always an option..."

Once you understand that statement, plus a little bit of humility, makes life go a lot easier.

Like my laser guy who just told me to spend the extra $20 on a pizza and handed me his paint marker..


Sent from my SAMSUNG-SM-G890A using Tapatalk
Click to expand...

That's a fairly old looking Laser. Would you happen to know Who made it? Looks somewhat familiar to me.
 
DAVe3283

DAVe3283

Heavy & Slow
Sep 3, 2009
3,727
296
83
Boise, ID, USA
MarkBroviak said:
Amen to that! The amount of engineering involved with this is mind numbing to say the least. Tomorrow we will get to make some noise with her!!!:D
Click to expand...
Aaaawwwww yeeeaaaaahhhh!
Waiting for the video with bated breath. Gotta hear that sweet sweet music.

Good luck guys, here's hoping it takes everything you throw at it and asks for more.

Sent from my Cat S60 using Tapatalk
 
NC-smokinlmm

NC-smokinlmm

<<<Future tuna killer
May 29, 2011
5,203
363
83
At Da Beach
clrussell said:
I was thinking “Bust Out Another Thousand” however I feel $1000 won’t go far on this build.
Click to expand...

For my customers it's more like 10k... :rofl:

I'm an idiot though bc I'm seatrailing a 53 Omie Tillet on Tuesday, even though I send out invoices for them everyday...:roflmao:
 
kidturbo

kidturbo

Piston Tester
Jul 21, 2010
2,539
1,377
113
Somewhere On The Ohio
www.marinemods.us
cdbright said:
every time you guys post inhere i think it is him adding a video of those babies running under load on the dyno and i get super excited :happy2:
Click to expand...
Psych...

098a9eabb9de253ae09aa753e5459e1e.jpg


Sent from my SAMSUNG-SM-G890A using Tapatalk
 
2004LB7

2004LB7

Well-known member
Dec 15, 2010
6,993
2,150
113
Norcal
Am I seeing 557 hp and 900 torque? And only like 550* egt? If so I like where this is headed
 
kidturbo

kidturbo

Piston Tester
Jul 21, 2010
2,539
1,377
113
Somewhere On The Ohio
www.marinemods.us
Mark has some gopro video of em. I just have the data views.

Short, it survived day one of testing. Didn't push it hard cause wanted to verify some low end stuff and check piston coating. Learned big lmm sticks and fingers pistons equals 12v Cummins exhaust look. And turbos are slightly bigger than anticipated.

Sent from my SAMSUNG-SM-G890A using Tapatalk
 
kidturbo

kidturbo

Piston Tester
Jul 21, 2010
2,539
1,377
113
Somewhere On The Ohio
www.marinemods.us
2004LB7 said:
Am I seeing 557 hp and 900 torque? And only like 550* egt? If so I like where this is headed
Click to expand...
EGT was actually 10-11 loaded there. But still well within our target. Cyl press under 3k, drive pressure beloe boost. So gonna swap out these lmm tips for lbz, hopefully clean up the pipe in this 600hp range. Then see if these turbos will light with some more fuel.

Sent from my SAMSUNG-SM-G890A using Tapatalk
 
kidturbo

kidturbo

Piston Tester
Jul 21, 2010
2,539
1,377
113
Somewhere On The Ohio
www.marinemods.us
2004LB7

2004LB7

Well-known member
Dec 15, 2010
6,993
2,150
113
Norcal
First video sounds like maybe an injector tick on driver side.

How was the exhaust smoke at 3600 rpm? Was that with a load/brake?
 
kidturbo

kidturbo

Piston Tester
Jul 21, 2010
2,539
1,377
113
Somewhere On The Ohio
www.marinemods.us
Exhaust smoke isn't excessive for say a 550hp truck, but it is for a 900hp diesel boat running at 50% load. Gonna swap these tips out to LBZ and try it again.

Here is little video inside the crankcase checking pan baffle flow. Little more oiling action in there than I was actually expecting. But it isn't stacking up, so that's good.

https://youtu.be/lWDmkxhixuE
 
Last edited:
You must log in or register to reply here.
Top Bottom