"OFFICIAL" What did you do to your D-Max today?

[Muff]

Thanks man. It def turns a lot of heads.

 

[malibu795]

Upper lower BJs and new pads

 

[ThebigGids]

Got the motor running for the first time in over a year!!!!:happy2::happy2:

 

[superswamper003]

Upper lower BJs and new pads

How was taking that big nut out thats holding the cv to the spindle? knuckle? Im not sure

 

[hondarider552]

Its not bad, my skinny ass can get it off.

 

[motoking_1990]

Installed new headlights and all new front suspension and steering parts.

 

[motoking_1990]

36mm and air

 

[minerigger]

36mm and air

Only way to do it

 

[malibu795]

How was taking that big nut out thats holding the cv to the spindle? knuckle? Im not sure

1/2" impact and 36mm socket.. And really easy

 

[clrussell]

Installed my roll pan and cute little exhaust tip

De-badged and removed all the tape from the flares / molding on the bed. Then gave it a quick bath.

Before

After

 

[Hot COCOAL]

bought a DP stg2 3794va today...
gawd DAAAAYYYYM it's about time, if everything gets here on time my truck will run again on Saturday morning:woott:

:spit:
it only took 8mo for me to replace my broken stock engine....
with a re-man stock engine :rofl:

:roflmao:

really tho, I got allot more than just the engine...just not enough to do what I want

 

[malibu795]

Lift pump on my tow pig died.. Motor was only drawing .5-.6amps vs 4-5 amps.. Gutted the pump primmed the fuel system and rolled out.. 70.00 Jegs pump lasted ~75,000 miles

 

[Xscout]

LAid hands on my '02 2500HD & prayed for it! It's got a gremilin infestation! :roflmao:

 

[c20elephant]

bought a DP stg2 3794va today...
gawd DAAAAYYYYM it's about time, if everything gets here on time my truck will run again on Saturday morning:woott:

:spit:
it only took 8mo for me to replace my broken stock engine....
with a re-man stock engine :rofl:

:roflmao:

really tho, I got allot more than just the engine...just not enough to do what I want

8 months, your fast... when you gonna put the cocoa puffs bird back in you avatar... That commercial when I was a kid made me want to kick the TV and brings back a lot of ruff and tumble days that I'm paying for today...

Today hopefully work on the EGT gauge mount, need my manifolds back, hint Yellowchevy...

 

[e46_330i]

Threw on a 30" light bar I had. Should compliment the all on mod & 55w hids well.

Sent from my iPhone using Tapatalk

 

[superswamper003]

Threw on a 30" light bar I had. Should compliment the all on mod & 55w hids well.

Sent from my iPhone using Tapatalk

I ordered the exact same setup!! That same grille, and a 30" bar.. Should be here soon hopefully

 

[e46_330i]

I ordered the exact same setup!! That same grille, and a 30" bar.. Should be here soon hopefully

Nice! Had it sitting right on top of the trans cooler at first but had to move it in front of it and down a tad. Fits tight but it's there. About 1/2" away from the trans cooler and touches the grill on the sides. Perfect fit! Was going to try a 40" but a few leds would be covered on the side.


Sent from my iPhone using Tapatalk

 

[Akers]

I dont do near as much as most of you guys but I finally got EFI Live for my LBZ. I went with the level 1 autocal from Kory and a dsp5 switch. I'm amazed at how much better my truck drives on his 100 horse tune vs the 100 horse tune on the edge evo I was using. It clicks right through the gears like butter now. With the edge it was a jerky ride. His tunes are also super clean which is what I was after. Even at WOT I won't get much more than a puff of smoke.

Now I just want to build the transmission and go faster!!

 

[hondarider552]

Finally installed the bottle heater since its getting cooler.

 

[duramaxzak]

Finally installed the bottle heater since its getting cooler.

How about some pictures of that new remote mount set up!