"OFFICIAL" What did you do to your D-Max today?

minerigger

Active member
Dec 24, 2013
2,660
1
38
Casper, WY
Replaced my airdog 165 motor. Freak when I though I lost the clip to hold the return fuel line off the pump to the tank. Not sure how but it made it safely into the frame rail...thank god. The directions said to remove endcap from old motor and install on new motor. Why when the new one comes with one on it. I didn't so hopefully it's got o rings and whatnot or I'll be needing another one. This new motor is loud as hell compared to the old one. Hopefully I don't go through this again anytime soon.

Sent from my SM-G900V using Tapatalk
 

malibu795

misspeelleerr
Apr 28, 2007
8,246
550
113
42
in the buckeye state
Was going to dyno my LMM but didn't get done in time to pull duals and run up to Firepunk Diesel do took my wagon up

First time she has been on a dyno in ~6 years and some 60,000miles. did 305/432 with 200 miles on it and smaller tires
12998767_10208379081728202_1057203818415070803_n.jpg

13051634_10208379142129712_2173984601521559232_n.jpg


Kinda stoked :)
Video of lavon running her on the dyno
https://youtu.be/XZuIUWsb-jc
 

c20elephant

C20ELEPHANT
Apr 25, 2013
2,065
0
0
Phoenix, Arizona
Replaced my airdog 165 motor. Freak when I though I lost the clip to hold the return fuel line off the pump to the tank. Not sure how but it made it safely into the frame rail...thank god. The directions said to remove endcap from old motor and install on new motor. Why when the new one comes with one on it. I didn't so hopefully it's got o rings and whatnot or I'll be needing another one. This new motor is loud as hell compared to the old one. Hopefully I don't go through this again anytime soon.

Sent from my SM-G900V using Tapatalk

Do you have a draw straw or a sump..?
 

minerigger

Active member
Dec 24, 2013
2,660
1
38
Casper, WY
Well I'm trying to get one. Also need some optilube. Trying to figure out what they do with the factory pickup on the top of the tank so it's not open?

Sent from my SM-G900V using Tapatalk
 

matt78

Finally boosted launches
Sep 10, 2012
924
0
0
texas
Installed my baseplates on my tow bar kit from blue ox. Should be pulling her behind the rig in no time.
 

UGAfsuFAN

New member
Sep 29, 2015
57
0
0
Between VA Beach & Tallahassee
Left Suncoast Converters shop today with my newly built transmission with a Limitless converter! Wow! What a difference! Awesome job! Gotta get a bigger fluid cooler next! Any suggestions?

Sent from my SM-N920V using Tapatalk
 

whitetrash21

put on da damn helmet day
Apr 29, 2008
4,929
0
36
Vegas
Was going to dyno my LMM but didn't get done in time to pull duals and run up to Firepunk Diesel do took my wagon up

First time she has been on a dyno in ~6 years and some 60,000miles. did 305/432 with 200 miles on it and smaller tires
12998767_10208379081728202_1057203818415070803_n.jpg

13051634_10208379142129712_2173984601521559232_n.jpg


Kinda stoked :)
Video of lavon running her on the dyno
https://youtu.be/XZuIUWsb-jc

Haven't seen that around in a while. Sounds like its still running good
 

lts1ow

Needs moar PAH!
May 14, 2012
1,598
0
36
NJ
Hauled three loads of mulch for my parents house, first one was 3yd and def at or above gvwr :D Pretty sure I convinced my Dad to get a baby dmax Colorado after that drive home. :thumb:
 

JoshH

Daggum farm truck
Staff member
Vendor/Sponsor
Feb 14, 2007
13,716
779
113
Texas!!!
I didn't do it today, but I finally welded in the bung and installed the coolant level sensor I got from Dave at HSP a couple of months ago. I hate welding aluminum...
 

Attachments

  • image.jpg
    image.jpg
    68 KB · Views: 54

malibu795

misspeelleerr
Apr 28, 2007
8,246
550
113
42
in the buckeye state
Delivered couple loads, washed the truck, then built a tail pipe. With a flex pipe coupler. Been busting up hangers when it was all one piece. Got pissed off dumped it in front of the axle.. Now it kicks out at a ~45° just in front of the bumper with a 24" flex joint underneath the tank.