Lock up controller Finally !

[LarryJewell]

Well...like Mike said.. I've technically had them for 2 years but I never advertised them very hard.

Brayden

Is this the same technology as is in the turbo brake :hello:

 

[jpowel29]

60ft 1.568

330 4.68
1/8 7.349
mph 91.71
1000 9.67
1/4 11.638
mph 114.17

:happy2:

other run was within .03 on et , on a 1.58 60ft

Wow!

 

[dmaxn04]

So what are the programmed for? Certian MPH? I think thats awesome! That you can just turn it on. The dodge I had, I put one on it but you had to manual lock it and unlock it when you wanted and if you forgot to unlock it, it would stall the motor when slowing down to a dead stop.

 

[serpa4]

Had a short wire on the old ferd. Forget to flip the switch approaching a stop light, chug, chug, dead engine: flip switch, restart engine.

 

[MadMooseEngineering]

Just a question probably answered earlier, but would this work with a stock converter or should it be used only for aftermarket ones.

 

[RPM Motorsports]

Just a question probably answered earlier, but would this work with a stock converter or should it be used only for aftermarket ones.

I think the word "Converter" should be replaced with input/output shafts, Im sure it will allow more torque to the ground sooner.

 

[MadMooseEngineering]

oh i c i need to stay away from these for awhile then til me tranny gets built

 

[dmaxn04]

Had a short wire on the old ferd. Forget to flip the switch approaching a stop light, chug, chug, dead engine: flip switch, restart engine.

Thats exactly what the dodges do.. Forget and it will scare the hell out of you if your not expecting it lol..

 

[Brayden]

Stock converter will work OK for a while at moderate power levels.

This shouldn't hurt shafts.. It's still a PWM apply.

 

[MadMooseEngineering]

Whats moderate i am making about 100 horse over stock and all my tranny has right now is a trans go jr kit

 

[Brayden]

I'd say 100hp is right on..

 

[MadMooseEngineering]

hmm i might have to save up and give this a whirl in my truck

 

[paint94979]

hmm i might have to save up and give this a whirl in my truck

Build your trans first

 

[dmaxn04]

Stock converter will work OK for a while at moderate power levels.

This shouldn't hurt shafts.. It's still a PWM apply.

Sent ya a pm brayden

 

[duratothemax]

Stock converter will work OK for a while at moderate power levels.

This shouldn't hurt shafts.. It's still a PWM apply.

x2...I agree...as far as the hard parts are concerned, this isnt any different than when the TCM itself applies the converter clutch.

 

[Brayden]

I did speed the apply up a bit, but it's about like a factory apply... We watched it on the scope and then trimmed a few hundred microseconds off it I could make that calibratable as well if people were having issues with wheel spin from a quick apply..

Brayden

 

[hdd-max]

Very nice

 

[Brayden]

Thanks..

BTW.. How do you like that fuddle converter?

 

[hdd-max]

Fuddle converter works very well. I did however have a heck of a time getting it from them. They were having some serious customer service problems a few years ago. I don't know if that has been fixed or not.

 

[serpa4]

If it locks by MPH and 95% throttle, guess it wouldn't work for street driving to lock the tc for increased mpg while driving slow in the city? Interested in having it lock as low as 25-30, but with almost no throttle and less than 5 psi boost.