Broken Crankshaft Count?

Please pick the one that you had break

  • Total voters
    185
sickdiesel

sickdiesel

New member
Apr 22, 2010
1,019
0
0
Harbin_22 said:
Just wondering for you guys that have bent/broke a crank. I drove it about 3miles home, ran for maybe 15min in the shop, and I can't see any signs of metal in the oil. I would think it should have been beating the mains out of it with that much run time.
Click to expand...

verlon drove his close to 400 miles after breaking his and 2-3 1/4mile passes.

bearings still looked fine. now this isnt common i would imagine but just a FWIW
 
Harbin_22

Harbin_22

Active member
Dec 4, 2010
3,858
7
38
Southern Indiana
More than likely. Seems logical if it is broke to try to keep from it again. Big question will be to buy a new crank or find a used one and get it checked out.
 
NC-smokinlmm

NC-smokinlmm

<<<Future tuna killer
May 29, 2011
5,201
363
83
At Da Beach
Harbin_22 said:
Might be adding another the list. Going to pull my engine this week and tear it down I believe.

Went WOT on the race tune from 3rd through 5th, slowed down to 30mph or so to make sure it was out of 4wd and when I started to speed back up, had a terrible vibration. Balancer appears to be wobbling. Balance rates are good, but getiing a cylinder 1&2 misfire. Took converter bolts out to rule it out and the vibration is still there. Balancer key is still good. May get an oil analysis because I can't see any metal in it yet. Might swap some injectors around and do a compression test but I feel like I am pissing in the wind.

Anybody let me borrow a match?
Click to expand...

Damm...:mad:
 
PACougar

PACougar

Active member
Jun 27, 2012
2,105
1
36
41
El Dorado Hills, Ca
That sucks! I'm not so keen on using a new crank only because it seems like they can have casting flaws in them from the factory. It's like a crap shoot from what I've seen. Either way I'd get it inspected.
 
LBZ

LBZ

Super Moderator
Staff member
Jul 2, 2007
9,903
149
63
46
B.C.
Burn Down said:
Cut the filter first. It's the best way to determine what is going on.
Click to expand...

I never found anything in my filter. And hardly anything in the pan. Didn't run a whole lot though once it started vibrating. Maybe 5-10 min on the Hwy before it shut down.

Sent from my C6906 using Tapatalk
 
Burn Down

Burn Down

Hotrodder
Sep 14, 2008
7,092
28
48
Boise Idaho
LBZ said:
I never found anything in my filter. And hardly anything in the pan. Didn't run a whole lot though once it started vibrating. Maybe 5-10 min on the Hwy before it shut down.

Sent from my C6906 using Tapatalk
Click to expand...

Normally with any engine noise it will tell you what you want to know or not know... No debris, there is a chance. Loaded filter, your Phooked:D but there are always exceptions.
 
Harbin_22

Harbin_22

Active member
Dec 4, 2010
3,858
7
38
Southern Indiana
Well she is setting on the floor with a wiggly balancer. The more testing I did, the more noise started happening so I said the hell with it and pulled it. When I took the belt off, the balancer was flopping around. When this first started, you couldn't move the balancer so it didn't take long to go ahead and break.
 
You must log in or register to reply here.
Top Bottom