Search results

Search the forum Search Articles
  1. JDPlowboy

    Clearing alternator with banks big hoss Intake

    I have dual fuelers tho
  2. JDPlowboy

    Clearing alternator with banks big hoss Intake

    Anybody have any insight on this? I have seen it done, just not sure how it was accomplished, I'm not afraid to cut up brackets as I have a few spares on hand. I spoke with Eric merchant and he cut up a stock lly bracket and flipped it upside down to make his work. I'd prefer not to have to weld...
  3. JDPlowboy

    4x4 end play

    Bingo. Thanks everyone for help.
  4. JDPlowboy

    4x4 end play

    So with the pan off and trans on its back, pouring oil into sump oil gushes out of test port as I spin it by hand, with valvebody back on, filter in and 2 gallon of oil in the pan, rolling it over by hand doesn't get me any oil at the test port. So I guess I'm getting a bad seal at filter
  5. JDPlowboy

    4x4 end play

    https://vimeo.com/154510094 Now I move forward to valvebody I guess?
  6. JDPlowboy

    4x4 end play

    Same valves, same springs since the original build
  7. JDPlowboy

    4x4 end play

    All the stator valves are free moving and came right out. I hate to do this without finding a problem but looks like I'm gunna have to find a new stator, pump, and comverter housing.
  8. JDPlowboy

    4x4 end play

    suction passage dry as a bone
  9. JDPlowboy

    4x4 end play

    so, I can check that Off list
  10. JDPlowboy

    4x4 end play

    Ok, I'll see what I find. Just about have it on the stand
  11. JDPlowboy

    4x4 end play

    So if I turned trans over on its back, poured oil in filter hole, put a handle In converter and spun it should squirt oil out ? Would be nice to check before I put back in truck again
  12. JDPlowboy

    4x4 end play

    How fast does the pump have to spin before it creates pressure? I'd like to figure out a way to spin it to see if I've solved it before I reinstall again. Even if it would just bump my gauge I would be happy and would save a couple hours
  13. JDPlowboy

    4x4 end play

    Thanks, I've done a few of these now but I feel so dumb right now. I'll pull it out for the 6th time tomorrow and look at stator. Didn't think about the stator shaft twisting.
  14. JDPlowboy

    4x4 end play

    02 5 speed suncoast 1056, gmax 5-1. Ratio tek hydros, transgo jr with Mike's trim springs. Pulled the stator apart none of the valves were sticking. The pump had some scoring so I replaced it and the wear plate.
  15. JDPlowboy

    4x4 end play

    Probably some bad voodoo since I questioned mike lol
  16. JDPlowboy

    4x4 end play

    I can see thru the plate at all the openings and all the bolt holes line up. Problem started after I swapped valvebodies after the truck hung the b trim valve on test drive after the re assembly. So in have no idea why it's showing up now. And not before
  17. JDPlowboy

    4x4 end play

    Now you guys get to poke fun some more. Been banging my head on this one for awhile. I've tried 2 different shallow pan filters, new bell housing gaskets gm part # 29536478 and 29540130 and finally a new pump. Still no line pressure at port, and fluid doesn't pull down off of dipstick. P0701 code.
  18. JDPlowboy

    4x4 end play

    Ya the rear thrust tho is one that has a collar and if it was upside down the collar would be supporting the shaft instead of the bearing surface. Now that this one is correctly assembled it shouldn't have anymore problems
  19. JDPlowboy

    4x4 end play

    I see
  20. JDPlowboy

    4x4 end play

    Not saying that's impossible but shouldn't it have failed sooner than 1000 miles?
Top Bottom