Search results

Search the forum Search Articles
  1. ikeG

    LML Coil overs for stock/lowered trucks

    On our sled puller we made a plate that bolted down using the sway bar link hole as well as the lower shock mount threaded bolt holes. We then used proformance pros lower mount I mentioned earlier. We only ran 1 coilover and used the other side(front) of the plate for suspension stop. If you...
  2. ikeG

    LML Coil overs for stock/lowered trucks

    Those pics are of a sled puller, I posted them to show the upper mount design they use. This truck would not be street driven ever again Sent from my SM-G960U using Tapatalk
  3. ikeG

    LML Coil overs for stock/lowered trucks

    They dont show the lca specifically in any pics. They sell a handy lower shock mount though. It is a direct replacement for the oem one but uses the correct size bolt and centering bushings for the afco coilover Sent from my SM-G960U using Tapatalk
  4. ikeG

    LML Coil overs for stock/lowered trucks

    Sled puller Sent from my SM-G960U using Tapatalk
  5. ikeG

    LML Coil overs for stock/lowered trucks

    Proformance pics Sent from my SM-G960U using Tapatalk
  6. ikeG

    Frame stretching

    Just roll the axle back to your desired wheelbase, then weld it all up. You could lose a lot of weight by fabbing your own rails and keeping them to a minimum just enough to meet the rules. Depending on your hitch location/design you may not need to lengthen the rails at all. Sent from my...
  7. ikeG

    Allison 5sp: Best Clutches Per Pack on 1000hp+ Build

    4-3 downshift while pulling [emoji2357] Sent from my SM-G960U using Tapatalk
  8. ikeG

    Seriously?

    Yea, you can see it in the pic broke off Sent from my SM-G960U using Tapatalk
  9. ikeG

    Seriously?

    Actually it is held in perfect isolation from anything by a little bracket attached to a valve cover stud. The closest thing to it is injector return line [emoji848] Sent from my SM-G960U using Tapatalk
  10. ikeG

    Seriously?

    When you see it... Sent from my SM-G960U using Tapatalk
  11. ikeG

    Allison 5sp: RCLB Sled Pulling Setup HELP

    If you change the rear stops to allow 1 or 2 inches of travel, un chain the front, leave the torsion keys out, you should have no trouble. Put the hitch at the max allowed unless it's ridiculous Sent from my SM-G960U using Tapatalk
  12. ikeG

    Allison 5sp: RCLB Sled Pulling Setup HELP

    So you put the rear travel stops in after raising the ride height 4-6"? If I'm reading right that's a big issue. Also chaining/strapping the front down will put you in all the good fail vids... Sent from my SM-G960U using Tapatalk
  13. ikeG

    Allison 5sp: RCLB Sled Pulling Setup HELP

    What is the max weight in the class? If its 8k you definitely want to invest the effort to get it there. Sent from my SM-G960U using Tapatalk
  14. ikeG

    Allison 5sp: RCLB Sled Pulling Setup HELP

    The bolts are out but are they stock keys? Sent from my SM-G960U using Tapatalk
  15. ikeG

    Mahle Wavestopper Grade D Head Gaskets

    No Sent from my SM-G960U using Tapatalk
  16. ikeG

    Mahle Wavestopper Grade D Head Gaskets

    We ran D's on an engine for a couple seasons at over 1k hp. That engine is still going strong in a 900hp street truck. Sent from my SM-G960U using Tapatalk
  17. ikeG

    LB7: Biggest turbo

    In my experience, you don't want to run a borg 96 tw unless you are on a budget and/or care about steet driving characteristics. An all out setup needs gt50 minimum as a single. A few shops are jamming a gt50 turbine into a borg housing, that's probably worth trying. Especially if valley...
  18. ikeG

    Allison 5sp: New Shop Do's & Don'ts

    Laid it out today. Should be 6 ft between lift posts. 3 in a row. 7 ft between lift post & wall. I think tests pretty roomy. Anyone have a shop with side by side lifts to compare? Sent from my SM-G960U using Tapatalk
  19. ikeG

    Allison 5sp: New Shop Do's & Don'ts

    Thanks guys, keep em coming. Want to do it right, think of everything. I'm not starting from scratch. I'm moving from our dealership to my own place. Taking all tools and equipment with me. Need a new building, lifts, air system is all. Sent from my SM-G960U using Tapatalk
  20. ikeG

    Allison 5sp: LML piston difference

    Thanks Jon. Sent from my SM-G960U using Tapatalk
Top Bottom