Search results

Search the forum Search Articles
  1. MAXLLY

    Trapped at work... chompin' at it

    I hope i run faster scared than you do pissed off......:rofl:
  2. MAXLLY

    Trapped at work... chompin' at it

    Slow season here... waiting for everybody to count the money and start sending out plans again. I wanna leave and go work on my truck. I know the Jegs site in and out, hand drawn my cooling, IC and oil system on paper, ordered nicer fittings, been over to Parker 3-4 times in the last couple...
  3. MAXLLY

    New pics of the Blower and Twin turbos!!

    I toought de truck was older and had one o dem boxes...:dunce:
  4. MAXLLY

    New pics of the Blower and Twin turbos!!

    I hear ya, but he already made the manifold... so fab and driveability isn't the issue! :D I see all custom stuff. DS exhaust around steering shaft? Maybe move the motor forward? that'll be tight. batteries in back, move or wrap the FICM next to the PS turbine, make new power steering lines...
  5. MAXLLY

    New pics of the Blower and Twin turbos!!

    Driveline could be a blessing until you get all the bugs out of her... The cheapest thing to replace is the driveshaft... tear up a couple of those, trans is $$$$, motor is $$$$, rear ends don't grow on trees... A weak link isn't always a bad thing IMO.
  6. MAXLLY

    Info: need a taller slick?

    http://www.jegs.com/i/Hoosier/522/18780C2055/10002/-1# IIRC- used to be the tallest readily available was about 30" +/- from M and H? This Hoosier is 34.5 tall and is purdy wide.
  7. MAXLLY

    New pics of the Blower and Twin turbos!!

    Wow... Nice!! thats gonna take some work. Going in a DMAX truck?
  8. MAXLLY

    AN fittings for my turbo

    Simon, Search function for me works like a runny nose... Didn't you have your own thread about ur build? The intake you made was pictured in it, no?
  9. MAXLLY

    Where to install an oil temp sending unit?

    I took the factory cooler apart... I can't memmer what is provided at the cooler, unfortunatley the pump is with my truck, 1.5 hours North of me.:( I thought i memmer several fitting that feed the squirters... in the side of the block. Take one out and convert it to AN or NPT. Here is...
  10. MAXLLY

    Sweethearts candy

    Since we are testers... I would say nuke 'em in the micro see what happens... Then try the oven... maybe 5 minutes at 350* soak them in sugar water for 5 minutes? Map gas flame thrower? put them in a vise and squash them... put them in a plastic bag and hit them with a hammer...
  11. MAXLLY

    Side Pipes?

    I only got the Ford pictures but i think it looks cool helps stretch it out and make it look lower by "soaking up" the margin between the ground and truck. What happens when she takes that lowered beast into a gas station with a steep approach?:eek: scrap pinch oh sheeeet? honey backabackup...
  12. MAXLLY

    AN fittings for my turbo

    I think i thought i thought he was to? :) The more fittings i need the more i like the local Parker store (steel, o-ring, AN 4 to 20, swiveling 180 adapters) for the wierd stuff, I take in what i have and we always seem to come up with something better... helps i bring him lunch and offer...
  13. MAXLLY

    Question: How is your suspension set up?

    fairly custom 4 link and coils in rear, drop spindles and keys in the front. Can't tell you how it works, should take all the trans can dish out.
  14. MAXLLY

    Help: Power wire for electric fuel pump

    Perhaps you could flip the key on and use a tester to find a hot circuit and tap the buss at that location? use velcro and stick the relay to the side of the fuse box? I suck at using the search function but this issue has been discussed in detail. Sorry if that doesn't help, or i am not...
  15. MAXLLY

    AN fittings for my turbo

    http://www.jegs.com/webapp/wcs/stores/servlet/category_10001_10002_10019_-1_10267 Poke around in hear a little bit... you'll find what you need. Check Earls specialty stuff at the bottom of the link page i gave you AN to Metric, AN to NPT etc. Good luck Man. EDIT: if you wanna drain the...
  16. MAXLLY

    got the bed back on finally...

    nice, the quad bed could look swaeet. I hear you on the truck sitting for a year... My Wife purchased a dozen socks for my first drive and a box of kleenex for tears.:rofl: She wants the truck done worse than i do... she's telling me to find a local Mechanic to help with re-assembly.:cool2:
  17. MAXLLY

    Question: up pipes/return line

    Dan, Came by the shop a couple days ago. Didn't see you at the helm! Couple of questions, please. Noticed the new 2"? up pipes with probe ports. Nice. How muchie and can your guy make 'em "tied together" for a single gate? No chromie stuff please.:) Installed the other pump awhile back...
  18. MAXLLY

    Twin turbo help

    burnsstainless.com intakehoses.com make friends with the guy at the muffler shop and have him order what you want. If you live by Pat there is a major distributor center for tubing just down the road from him, other side of the 91 fwy.
  19. MAXLLY

    got the bed back on finally...

    Sweeet! I thought Nicks truck was low, damn....:D
  20. MAXLLY

    got the bed back on finally...

    Kyle, I don't get it? Sorry. Why do you have to frame over the bed? Is the top of the 1x steel (elevation the level is sitting on in the pictures) the support for the new bed bottom? and the original gets cut out? Not bashing, just wondering.:)
Top Bottom