Search results

Search the forum Search Articles
  1. MMLMM

    Thanks Dan/PPE

    Looks good
  2. MMLMM

    Removing & Installing Trans

    The bolts with rubberbacking go in center around pump, the bolts without go to bell housing on outside, the 2 with copper washers go in the bottom. Like said, us a little rtv on the center rubber ones just to be sure your not pulling it again.
  3. MMLMM

    e shift valve reamer,,,

    Oops....I was thinking the sizing tool. Not the reamer.
  4. MMLMM

    e shift valve reamer,,,

    Patc or a sonnex dealer
  5. MMLMM

    Billet aluminum block

    Stock Main Caps? What about lifters? Whats going on there? Stock drop in or what? Std. Bore? Or can we get +0.40" out of it over a stock bore?
  6. MMLMM

    Help: lmm maxed out rail pressure at idle

    Highly doubt this is an ecm issue. Ground, pinched wire, unpluged or not fully plugged in, twin cp3 controller, FPR or like dan said check fuel temp sensor.
  7. MMLMM

    Sema 2011

    Thursday night at Millers ale house @ Town Square @ 7:30PM Let me know if your going.
  8. MMLMM

    PPE Kit

    I have put quite a few PPE kits in and seen maybe 2 where the clearance was iffy in the PPE kit. We have extras here so its not a big deal for us. But again as many as we have done and only seen 2, I doubt you will run into an issue (Again this is the trans based on wear, snap rings, and such...
  9. MMLMM

    More PPE B.S.

    Why dont you guys order form a Authorized PPE dealer?
  10. MMLMM

    LMM: [email protected] to do now

    Little more timing will help with the pulse you are running. You are not seeing it because your not hitting that rpm, double check where that 30 degrees is at on your table, chances are is pretty high. Also dont forget your max timing table. Another thing to remember is tire pressure. Play...
  11. MMLMM

    LMM t-case/lb7

    Awesome, We figured it would work but wasnt sure with the case difference. Im trying to ding into wiring and seeing what I can come up with Jason. Cant be too hard. Anyway glad the roll of the dice :D so far has worked out. :thumb:
  12. MMLMM

    Tcase question...what will fit?

    Which tcase will fit in what trucks? I know lmm is a little differnt butwill it work in lb7? If not could simple parts be swapped to work?
  13. MMLMM

    P0734??

    Who tuned it, I know you know... :D /Stirpot
  14. MMLMM

    Drop in batmowheel

    There is a better reason why the wheel is not a drop in lol.... Maybe BE will say, maybe not.
  15. MMLMM

    So.........

    Hit one of us Vegas guys up when your here. We'll grab drinks with ya.
  16. MMLMM

    las vegas

    call me, there is a bunch of stuff going on at the strip tonight. Or swing by the shop on weekdays for a visit. Or we can all meet up and grab some food and drinks one night. We'd be happy to show you around man. If you need club info let me know. MIke 702-232-two-zero-four-eight
  17. MMLMM

    Interseting Trans issue after rebuild 5-speed in an 01

    :banghead: <-- this simile says it all! Thanks again Mike, I tried to call back and let ya know. I was about ready to pull the trans apart and see where I F'ed up, but truck runs Great now!
  18. MMLMM

    Interseting Trans issue after rebuild 5-speed in an 01

    Thanks Dan and Mike L. They both pointed to speed sensor which I had already changed which is why I was stumped. However, Here is a tip, if you are trying to track down a sensor issue, use a new sensor and not a "should be good" sensor :D
  19. MMLMM

    Interseting Trans issue after rebuild 5-speed in an 01

    Another thing, Input Speed is like 1300rpm and when you put into drive, it goes to zero. When I tested on a truck that runs correctly, Input is same as engine rpm, and normal in D.
  20. MMLMM

    Interseting Trans issue after rebuild 5-speed in an 01

    Not 100% sure on ign switch, but ign was working and seems to be working correctly??? TAPS have been reset
Top Bottom