Search results

Search the forum Search Articles
  1. duramaxzak

    LML Tranny failure

    Yep! And I believe the dealer is the one who damage the tranny on there diagnosis test drive.
  2. duramaxzak

    Planned build

    It's about time! :thumb:
  3. duramaxzak

    LML Tranny failure

    Got my truck back yesterday. It ended up costing me $747.45 out of my pocket for a new TCM and new transmission and torque converter. It cost GM over $9k! The tranny alone was $7800 plus the labor of removal and install. This is the first problem I have had with the truck in 63,000 miles and...
  4. duramaxzak

    LML Tranny failure

    Hmm.... Anyone have a 11' warranty manual handy that could verifie that the TCM should be covered?
  5. duramaxzak

    Dodge brake conversation

    Are you still running a Allison? If so, Suncoast is working on a transbrake for the Allison. That might be a better route to go. http://www.duramaxdiesels.com/forum/showthread.php?t=60788&highlight=Transbrake
  6. duramaxzak

    Throwback Tuesday

    This is a picture of my first Duramax I bought in 2004. It was a 2003 with 26k on it.
  7. duramaxzak

    LML Tranny failure

    As of now, yes!
  8. duramaxzak

    LML Tranny failure

    Update: Got a call yesterday that they finally got the new tranny and in the truck, but it is still acting weird and hunting for gears the service guy said. So now they are saying that the TCM is bad and that is what caused the tranny to destroy it self in the first place and that the TCM is not...
  9. duramaxzak

    Help: Grizzly Locker Install

    No additives needed since it does not have clutch packs like a limited slip diff., but I would use a good synthetic gear lube.:thumb: No test video's!!!
  10. duramaxzak

    Duramaxzak 2.6 pulling truck build

    Put my tranny blanket on yesterday, kind of a PITA getting it over the top of the tranny with it in the truck!
  11. duramaxzak

    Duramaxzak 2.6 pulling truck build

    I bought it off a member on here, not sure who makes them.
  12. duramaxzak

    Duramaxzak 2.6 pulling truck build

  13. duramaxzak

    Duramaxzak 2.6 pulling truck build

  14. duramaxzak

    Duramaxzak 2.6 pulling truck build

    I have been tying up alot of loose ends lately. Got all my pumps and fans wired, finished up putting the lids on the weight box it just needs some grinding and a paint job.
  15. duramaxzak

    LB7: P&p IHI with billet wheel vs stealth 64mm

    Here's a couple video's of my truck last summer pulling with DTS's Billet 66 IHI http://youtu.be/Taunytl6vQQ http://youtu.be/oONgaVcCpKI
  16. duramaxzak

    LB7: P&p IHI with billet wheel vs stealth 64mm

    DTS's 64 IHI made 599hp with 45% injectors and LBZ cp3. I believe DTS makes the stealth 64 IHI for Duramaxtuner.
  17. duramaxzak

    Duramaxzak 2.6 pulling truck build

  18. duramaxzak

    LB7: P&p IHI with billet wheel vs stealth 64mm

    I have ran DTS's 64 and 66 IHI turbo's. The 64 came with a cast compressor wheel and stock sized exhaust wheel. The 66 had a billet compressor wheel, but used a S300 center section and the IHI exhaust housing with a 74mm wheel. The 64 spooled like stock, but pulled harder on the top end than...
  19. duramaxzak

    Duramaxzak 2.6 pulling truck build

    I bought my 8" BS wheels used with the intent on removing the rear leaf springs and welding the axle in, but am consider leaving the leaf springs on it now.
  20. duramaxzak

    Duramaxzak 2.6 pulling truck build

    Yep, 10" wide with 8" BS Realwheels. Pm me a price shipped to 55398! Not sure if I'm going to have time to get the rear axle welded in this year.
Top Bottom