Search results

Search the forum Search Articles
  1. C.bowles2

    suncoast built trans

    Yes i did Sent from my iPhone using Tapatalk
  2. C.bowles2

    Is an cp3 upgrade needed for me?

    How exactly can i change the shift points to keep it in the happy zone? V2? And the al5 controller? All i have is ecm tunes emailed with an autocal. Truck seems a tad bit sluggish especially off the get go, then builds boost fast and hard, then falls off at the top, probably because of the fuel...
  3. C.bowles2

    suncoast built trans

    Yea im asking because im running a 1058 with that turbo and my convertor knowledge isn't the best. I feel like my truck is sort of sluggish then what i thought it would be after my turbo install. Wasn't sure if it was my tuning, lack of fuel (stock co3 and sticks) or the convertor?? Sent...
  4. C.bowles2

    suncoast built trans

    Whats the best convertor for a 68mm billet stg2r? Sent from my iPhone using Tapatalk
  5. C.bowles2

    Dowel pins

    I was using a rubber dead blow hammer, maybe i need something with more umph. Ill try cleaning them up better. Also i put this bell housing on and forgot about the two sealing washers on the bottom two bolts. The ones with the washers are somewhere in there. Are those re-usable or should i just...
  6. C.bowles2

    Dowel pins

    So i have r&r'ed many transmissions in my day and im trying to install the dowel pins in the block and they dont really want to go in as smoothly as id like. The cone side facing me, and they are going in real hard. I tried some scotch bright pad and cleaned everything up and still same thing. A...
  7. C.bowles2

    Would you use this ats flex plate?

    Can convertor bolts be re used? Sent from my iPhone using Tapatalk
  8. C.bowles2

    Would you use this ats flex plate?

    I think thats what they did, they used the regular factory ones. Only thing with the twelve hole theory is the other six all line up but one is like an oval instead of a circle, ATS must have wanted it to go on with the other six holes. Mike where would i get longer bolts that are rated for the...
  9. C.bowles2

    Would you use this ats flex plate?

    I acquired a billet ats flex plate from a friend. Hick Town creations"built" and installed his trans and not very long after he got it home the torque convertor bolts came loose and eventually sheared off/came undone. Needless to say another one of their screw ups needed fixed. Anyhow this...
  10. C.bowles2

    Black Friday and Cyborg Monday

    Do you guys sell billet input shafts? Sent from my iPhone using Tapatalk
  11. C.bowles2

    Black Friday and Cyborg Monday

    Billet input shaft!!!! Sent from my iPhone using Tapatalk
  12. C.bowles2

    New turbo! Couple questions...

    It was working out great till my transmission input shaft broke! Haha i only have a couple hundred miles on it so far. I like it a lot though. It pegs my 35psi boost gauge. And the air just flows better and longer i think. Less lag also. Sent from my iPhone using Tapatalk
  13. C.bowles2

    Trans hydraulic upgrades

    Ahh ok, i used to have a 700r4 behind an old chevy 350 Sent from my iPhone using Tapatalk
  14. C.bowles2

    Trans hydraulic upgrades

    Nvm found the shift shaft seal, gm part number 24235861 or national number 710545 Sent from my iPhone using Tapatalk
  15. C.bowles2

    Trans hydraulic upgrades

    Well since my input shaft broke i have my trans torn apart. Couple questions, it has some hydraulic mods that fleece did but im wondering if there is anything else i should do or improve. Already have Mikes trim springs in it. Here is a pic of the two big valves in behind the pump. Is there a...
  16. C.bowles2

    Project #6FOKLLR

    Nice! Looks like a good clean build. What was the tome frame on it? Sent from my iPhone using Tapatalk
  17. C.bowles2

    Project #6FOKLLR

    What did you use to soak the high pressure injector lines? Sent from my iPhone using Tapatalk
  18. C.bowles2

    Doesn't get much better than this

    Definitely brought a smile to my face! Good stuff right there. Can't wait till i have kids. Niece and nephews are ok for now though! Sent from my iPhone using Tapatalk
  19. C.bowles2

    Allison 6sp: Built Transmission, now needing some help

    Also heres the end of the input mike, will i need so machine anything or is this the late style? Sent from my iPhone using Tapatalk
  20. C.bowles2

    Allison 6sp: Built Transmission, now needing some help

    Ok just did that! Haha ok im not familiar with what part is what so bear with me. Im working on getting the input out now. But i noticed the drum thing that holds the c1 steels has some wear and also the splines on the intermediate? Looks like they are curved? Here are some pics Sent from...
Top Bottom