Search results

Search the forum Search Articles
  1. bigbird

    Need chassis setup advice.

    I need some input from people on my setup. Truck will run 123mph in the 1/4 but my 60 ft.'s are brutal. 1.74-1.78. the best i have ever done is 1.70. I am running 30.5 in. tall Toyo proxies, caltrac's set at about a 1/4 turn preload, overload leaf pulled, and Rancho 9000's set on 1. Is it...
  2. bigbird

    NHRDA Edmonton May2 results

    NHRDA had their event in Edmonton. I ran in S/S and had 5 runs all between 11.41 and 11.76, MPH 119-123. some on motor some on a .54 jet. Made it to the finals and made a rookie mistake and had my foot slip off the brake (red light). The guy that won blew his tranny and ran a 16.0. 7 trucks in...
  3. bigbird

    Running no defuel

    If i was to run a smooth no defuel TCM tune in my truck, would the allison be able to handle it at around 750hp?
  4. bigbird

    Flash with EFI after replacing a cooked ecm.

    I will be replacing my ecm, which has gone to junk. after i replace the ecm, I have to get a new license and then do an full flash with EFI using my original VIN, correct? anything i am missing? thanks Kelly
  5. bigbird

    NHRDA May 2 in Edmonton

    anyone going? should be some fast trucks. http://www.nhrda.com/Flrz/0502.htm
  6. bigbird

    EFI Live. moron (me) needs help

    got a new laptop. downloaded the latest version then downloaded the drivers but can't figure out how to install them. all help appreciated. Kelly
  7. bigbird

    Caltrac setup.

    How do people have them set. I need to soften then i believe but am not sure which way to go. Do they make the rear feel extremely stiff running empty? mine feels like a brick. Kelly
  8. bigbird

    My 6 point rollbar pics.

    Got the truck back today.
  9. bigbird

    UPS just showed up.

    Finally showed up along with my wastegate. The pics are someone else's of the same pedestal.
  10. bigbird

    Bootloader rejected box

    Help, Bootloader rejected box I keep getting this box appearing when i try to load a different tune. Truck has been sitting awhile so it was suggested i charge the battery, which i did but is stll showing this box. also says "ecm in unknown state". anyone know why this would just start...
  11. bigbird

    Aftermarket up pipes and headers opinions.

    Anyone have any thoughts on these? are they worth the money to upgrade? are they reliable? thanks Kelly
  12. bigbird

    GT 42 pedestal spacer height.

    On the PPE GT 42 pedestal there is a spacer, anyone know how tall it is? Kelly
  13. bigbird

    T4 pedestal with wastegate.

    Anyone build one for an S400 or GT 42 sized charger?
  14. bigbird

    Help with info window. Security light on.

    The little info window in the left hand corner of my dash has the security light on and it will not go off. anyone know why? this is on an 02. Kelly
  15. bigbird

    Twins vs. big single

    I am having some trouble deciding between twinning my silver66 with a GT47 or going big single ie. Phatshaft 71, GT4202/magnum, s400, s480,etc.. cost is an issue in this decision, but the major concerns are to keep egt's, drive pressure and rpm's reasonable. my truck has run 11.45 and the goal...
  16. bigbird

    Twin turbo pics

    anyone have twin install pics from underneath of how the big turbo is mounted and supported. thanks Kelly
  17. bigbird

    one more converter question.

    I am debating going with a different converter. what are the drawbacks of a converter that is too loose? I am leaning towards a 58 or a 55. have haerd a few guys say they don't care for the 58. any reason why? Kelly
  18. bigbird

    Anyone run Florida today?

    anyone run the NHRDA event today?
  19. bigbird

    How much air needed to light a GT55

    what is the minimum turbo size I would need to light a GT55 in a compound setup? pretty sure i would need an S400, but am wondering if my silver 66 could light it and not be to laggy.
  20. bigbird

    Need converter opinions.

    I am going to be changing the setup of my truck. I am going to twin my 66 with an 81. I am leaning towards a 1055 converter. will this be too loose? I am open to suggestions other than the 1058. thanks Kely
Top Bottom