Search results

Search the forum Search Articles
  1. Houser04lly

    I must be stupid

    Find the small numbers on the connectors that plug into the ecm then just count over to the number u need there will be a blue pin in its place where the wires insert
  2. Houser04lly

    DSP5 install no start

    So I am a little ashamed because I have broken studs on the ECM itself where the ECM connectors latch . When you push the connector down on the ECM and slide the latch back it grabs on two plastic studs top and bottom of the ECM connector.. now its def not going to latch down enough for sure to...
  3. Houser04lly

    New drive, boost, and pyro gauges

    x2 on that
  4. Houser04lly

    DSP5 install no start

    I hate to say it but I think its gonna be new connectors .. I havnt got anywhere with it
  5. Houser04lly

    DSP5 install no start

    I hope today I can get it running. This is killing me
  6. Houser04lly

    DSP5 install no start

    I triple checked pins connecting to the ECM and on each connector the Blue, Black, and Gray. Hey phil what did you mean by you had one pin that was just 32" in .. all the pins looked exactly the same in place on each connector when I look at the connector face up if the locks also are not...
  7. Houser04lly

    DSP5 install no start

    The gray connector ECM is locked and all the pins were checked again .. but when I mess with the gray connector this is when I get any action at all out of the truck .. worst case I'm guess ill be needing new connectors.. what a mess that would be .. I'm going to check connectors again and again
  8. Houser04lly

    DSP5 install no start

    I greatly appreciate the help everyone ill keep posted
  9. Houser04lly

    DSP5 install no start

    Damn that's alot .of wires to check . I looked at the clip and all the pins looked equal .. this is gonna be a tough one
  10. Houser04lly

    DSP5 install no start

    Top
  11. Houser04lly

    DSP5 install no start

    Got the truck to run there's no boost and it keeps throwing pcm codes .. its def a bad connection at the ECM .. any thoughts ? Thanks for any suggestions I appreciate it .
  12. Houser04lly

    DSP5 install no start

    Got it fired up stays running .. just no power .. im confused its primed and it has new batteries ..
  13. Houser04lly

    DSP5 install no start

    Ok thanks man I appreciate that ill keep posted
  14. Houser04lly

    DSP5 install no start

    I'm not sure now I will def double check
  15. Houser04lly

    DSP5 install no start

    Also the middle connector on the ECM the black one wouldn't lock even with the lock slid back I.could pull it off by hand that's why I'm kinda thinking its an ECM issue I always run into stupid problems like this ..
  16. Houser04lly

    DSP5 install no start

    I actually did get it to fire last night and when she did it def sounded and felt as if she weren't hitting all cylinders.. then it wouldn't fire again after that
  17. Houser04lly

    DSP5 install no start

    That's weird I mean anything can happen
  18. Houser04lly

    DSP5 install no start

    I did check all fuses going to check again in the day light when I get home .. thanks for the input I appreciate that
  19. Houser04lly

    DSP5 install no start

    Just looking for some more suggestions.. installed DSP5 switch wired to the ECM Didn't flash it just basically hooked up the switch and now it .just cranks and doesn't fire up cranks maybe 4 times and cuts off . It does say reduced engine power on the dash display . I checked all the ECM...
  20. Houser04lly

    6.7 furd chip/box/programmer?

    My buddy did some research and hes going with the KEM 345 tune the shifting is way better and the power is much better than the spartan so he hears .. we will see when he puts it in .. im sure im the first person he's going to try and run down .. ill let you know how is headlights look from my...
Top Bottom