LMM: New Danville 68MM Stg2R Review

othrgrl

othrgrl

Diesel Addiction Owner
Mar 10, 2008
2,151
4
38
Wilmington NC
www.mydieseladdiction.com
Eeny, Meeny, Miney, Mo.

Can't wait to see what one of these Stg2R's is like in comparison to the other 3. By the way Shields, you need to call and get on the schedule for the trans, and while it's out.....
 

Attachments

  • IMG_20150216_114522797_HDR[1].jpg
    IMG_20150216_114522797_HDR[1].jpg
    198.7 KB · Views: 159
TowU4Free

TowU4Free

#SecretSquirrel
Aug 27, 2011
469
5
18
look at all those ! I'm assuming far left is the 3794 third over is the stg2r not sure about the other 2?
Btw Dustin do you remember an 07 lbz crew with 100s and a stroker pump? Dark grey, guy named Jonathan owned it? A good friend of mine owns it now he's in his 60s lol
 
othrgrl

othrgrl

Diesel Addiction Owner
Mar 10, 2008
2,151
4
38
Wilmington NC
www.mydieseladdiction.com
towu4free said:
look at all those ! I'm assuming far left is the 3794 third over is the stg2r not sure about the other 2?
Btw Dustin do you remember an 07 lbz crew with 100s and a stroker pump? Dark grey, guy named Jonathan owned it? A good friend of mine owns it now he's in his 60s lol
Click to expand...

Left is BMW3794, then the same turbo that is on the truck you mentioned, then the 68mm Stg2R, then the 72mm billet.

It's unfortunate for Jonathan that he had to let the truck go to buy or build a house, he still misses it. We did the turbo, 100 overs, 10mm stroker, tuning, and a few other things on the truck. The truck was really starting to dominate stock class then he sold it.
 
Last edited:
TowU4Free

TowU4Free

#SecretSquirrel
Aug 27, 2011
469
5
18
That truck is wicked man ! Its a shame it will never get put to full use anymore it's the fastest truck I've been in to date I'm trying to catch him !!
 
Last edited:
N

N2BRK

Well-known member
Dec 31, 2009
2,054
371
83
I run mine even lower, but I re-wrote my TCM to tune to keep it in 2nd and locked up until 8mph on decel in T/H mode. I get a lot more help coming to a stop sign than I thought that I would. If I wind up doing a slow roll and not a full stop, I can always pull 1st gear on the tap shifter to avoid a situation where I'm bogging down the truck trying to take off again.:thumb:
 
malibu795

malibu795

misspeelleerr
Apr 28, 2007
8,239
550
113
42
in the buckeye state
N2BRK said:
I run mine even lower, but I re-wrote my TCM to tune to keep it in 2nd and locked up until 8mph on decel in T/H mode. I get a lot more help coming to a stop sign than I thought that I would. If I wind up doing a slow roll and not a full stop, I can always pull 1st gear on the tap shifter to avoid a situation where I'm bogging down the truck trying to take off again.:thumb:
Click to expand...

1400 gets me below the downshift point when coming to a stop.. TCC engaged/disengaged at 11mph.. Problem I have is OEM TC is so loose (IMO) TCC won't engage on part throttle acc till 30mph basically 3rd when the truck is loaded, when starting out going up a grade.. I have always been under the impression the TCM won't engage TCC when there is more than 750rpm difference between engine rpm and input rpm on the transmission. Though I have not found any supporting data to back that up..
 
Y

yellowchevy

Well-known member
Sep 9, 2010
1,926
82
48
Louisburg, KS for now
I installed a 3794v today on an LMM for guy and it drove great. Very responsive and pulled hard through all the gears. It dropped a little when it shifted into 6th but very minimal. When comparing the stock LMM to the 3794, the 3794 was more responsive and drove great.

Not to mention it sounds good!!:D:woott:

Great job Mark, very nice work!!:thumb::thumb:

Yellowchevy
 
You must log in or register to reply here.
Top Bottom