Highest Stock CP3 HP?

TROJAN366

TROJAN366

Gold Rush
Jan 13, 2012
2,474
1
38
MASS
On a serious note, I would love to know what the highest fuel only dyno number is on a stock pump is. I will have an LBZ regulator but I think that is still considered stock?? I'd love to have that claim to fame haha
 
Noreaster

Noreaster

Active member
Jun 13, 2007
2,910
0
36
43
Cape Cod,MA
TROJAN366 said:
On a serious note, I would love to know what the highest fuel only dyno number is on a stock pump is. I will have an LBZ regulator but I think that is still considered stock?? I'd love to have that claim to fame haha
Click to expand...
with enough correction factor 700hp is possible
still going to be :gay: when you are stuck in the 12s
 
TROJAN366

TROJAN366

Gold Rush
Jan 13, 2012
2,474
1
38
MASS
Noreaster said:
with enough correction factor 700hp is possible
still going to be :gay: when you are stuck in the 12s
Click to expand...
AJ, the only reason you throw out the rainbow flag, is because deep down you have a crush on me lol. We'll see what happens. If it runs really deep 12s I'll be ok with it I guess. It'll just motivate me to get the 2xcp3 and 72 sooner
 
ryanvanl

ryanvanl

New member
Dec 4, 2012
11
0
1
I'm running a LBZ pump in my lb7 with 50% over injectors and last time I was in a NON-loaded dyno I pushed 672 to the rear wheels. So I believe its pushing more like 700+ on loaded dyno.
 
TROJAN366

TROJAN366

Gold Rush
Jan 13, 2012
2,474
1
38
MASS
If I made 700 on any dyno, even with a large correction factor, I would pee my pants and then cry tears of joy lol.
 
TROJAN366

TROJAN366

Gold Rush
Jan 13, 2012
2,474
1
38
MASS
I made 570 for a while with water meth and my rods all came out straight. But we found out the truck was on tune 3 not the hot tune. So who knows what would have happened if I ran it all out.
 
baggedLB7

baggedLB7

Goer
May 1, 2011
688
4
18
Utah
I ran 711 on the custom auto pull behind dyno last summer on stock injectors and stock cp3 but its one of the higher reading dynos and was deff kind to me.
 
quinton

quinton

Active member
Nov 28, 2011
1,883
0
36
Granbury Tx.
My cp3 is weak and am about to get 100 over injectors. I just want to be in the 650 range with my cp3. If not ill get a modded one from Danville. Right now I'm at 570
 
paint94979

paint94979

Beer Nazi
Sep 18, 2006
11,715
8
38
37
NC-smokinlmm said:
Too much torque down low bends rods...


We need to thank all those guys who figured this stuff out so our rods can stay straight...:D

Thanks fellas....:hug:
Click to expand...

You can PM Pat McRat McSwain and thank him personally... He pushed this idea way back in 06' and because of him my engine is still alive after beating the piss out it at big hp for 6 years
 
TROJAN366

TROJAN366

Gold Rush
Jan 13, 2012
2,474
1
38
MASS
dirty_max said:
haha thanks guys. so what is the hp/torque numbers before you start bending rods?
Click to expand...
In the past people were bending rods as low as 500hp. Now with good tuning there are some trucks running around at 700hp. Doesn't mean they will last forever, but it can be done.
 
You must log in or register to reply here.
Top Bottom