Search results

Search the forum Search Articles
  1. DPC

    ring end gap forged piston

    .010 PTW clearance, 85lbs boost.
  2. DPC

    ring end gap forged piston

    What ring end gap is recommended for forged pistons? I have Ross pistons with total seal standard file to fit rings. I called Ross they told me to call Total Seal, Total Seal said he could not give me a specific gap because diesels have too many variables, boost, nitrous, water meth, etc...
  3. DPC

    tranny leak round 3, help

    What did you do to break the input and then the output? Do you have your defuel turned off?
  4. DPC

    Brodix cylinder heads for the Duramax

    I did just call and ask them, I was told the project is being discussed, no dates yet. I told him brodix was making a dmax head and he sounded suprised.
  5. DPC

    New fuel only best for the dumpster

    I saw you run in Ennis this weekend, impressive. I laughed a little everytime I saw that thing going down the track. Looks like you spent a lot of money on paint...
  6. DPC

    06 Dmax, balance rates fuct

    Did you do a cylinder shut-off test?
  7. DPC

    Let's Talk About Electric Water Pumps

    Something like a coolant bypass kit used on the cummins? http://www.puredieselpower.com/catalog/1224v-coolant-bypass-kit-reduce-block-pressure-high-rpm-p-32358.html
  8. DPC

    Cranks

    Do we need to take into consideration what balancers were on the crank when broke? How many broke with ATI, Fluid, stock, etc?
  9. DPC

    Idaho dinosaur

    That fish is probably 50 plus years old.
  10. DPC

    Help! How to get kryptonite tierod into knuckle?

    ^^^ I have tried this and like you said the steering was horrible!!!
  11. DPC

    S475 upgrade to s480 question

    Yes.
  12. DPC

    S475 upgrade to s480 question

    I went from a 466 to 475 wheel. I took the center section to a machine shop and they turned it in a lathe. It only took about 20mins.
  13. DPC

    Grinding noise when turning left

    It is actually a cheap fix. Unbolt your half shaft from the flange, pull the shaft out and inspect for damage. Usually you just need to replace the retaining clip and push the shaft back in the diff. I know merchant sells them. http://www.merchant-automotive.com/stubshaftsnapring.aspx I would...
  14. DPC

    Gtx 4202

    Which precision are your running, PT7675 ?
  15. DPC

    Grinding noise when turning left

    It's the the shaft that comes out of the drivers side front diff. Your half shaft bolts to it.
  16. DPC

    Grinding noise when turning left

    Maybe a long shot but turn your wheel all the way to the left, craw under the truck and see if your stub shaft is pulling out of the diff. Possibly your retaining clip is shot?
  17. DPC

    4088r, 4094r, or s366?

    I have been running my 4094R since 2008. Tow, sled pull, and strip, love this turbo.
  18. DPC

    trans shop in okla

    What are you looking to have done? I have built a few with suncoast and ATS kits. I live in Elgin, OK.
  19. DPC

    LB7: II Lb7 injectors good??

    Mine lasted 23,000 miles. I replaced them with a set from Socal Diesel.
    • DPC
    • Post #9
    • Forum: LB7
  20. DPC

    Transfer case to go behind an Allison 1000

    Never said the t-case was better, just more front drive shaft options. you may be able to weld any tube to the yoke, but you can't upgrade the yoke to bigger u-joints. The front drive shaft on a dodge has a flange that bolts to it (t-case side). The front shaft on a GM has a male slide in...
Top Bottom