Search results

Search the forum Search Articles
  1. ikeG

    06 lly swap to 85 chevy

    The upper and lower oil pans are different. Kodiaks are front sump, which actually works in some apps. The y bridge and intake tube pressed into it are different as well. Exhaust manifolds and up pipes are different too. A lot of these differences may not need changing if not going in a...
  2. ikeG

    S480 96mm turbine

    Yes Sent from my SM-G960U1 using Tapatalk
  3. ikeG

    S480 96mm turbine

    That would be the best option in your scenario in my opinion. I have some experience with that exact setup and it did well on the street Sent from my SM-G960U1 using Tapatalk
  4. ikeG

    Triangle G-rated 16" trailer tires

    Personally I prefer circle tires. Triangles seem like they would ride rough Sent from my SM-G960U1 using Tapatalk
  5. ikeG

    Seriously?

    "Do it for the 'gram" is the common mindset these days, I believe. Sent from my SM-G960U1 using Tapatalk
  6. ikeG

    Stroker pump vs dual pumps

    A single 10mm pump should support close to 4 digits. Sent from my SM-G960U1 using Tapatalk
  7. ikeG

    LB7 build

    *.020". Looks like a good time Sent from my SM-G960U1 using Tapatalk
  8. ikeG

    LML engine knock

    It was owned by a dealership. They sold it. Explained the concern to the customer and everything. Never heard back Sent from my SM-G960U1 using Tapatalk
  9. ikeG

    LML engine knock

    Never found an issue. Still made the noise Sent from my SM-G960U1 using Tapatalk
  10. ikeG

    Seriously?

    It ended up having the wrong rotors. There is 3 different rotor part numbers for it, depending on the hub it came with. The depth of the back space is the difference, these washers kept the incorrect rotor from rubbing the knuckles. Sent from my SM-G960U1 using Tapatalk
  11. ikeG

    Seriously?

    Older jeep cherokee in recently. Nice surprise. Sent from my SM-G960U1 using Tapatalk
  12. ikeG

    Twins with Twins, Anyone?

    Assuming turbo shaft speed skyrocketed during the freerev, the turbo can't really be blamed. That has to be a large issue with turbos on boats? When they props come out of the water theirs really nothing you can do. Sent from my SM-G960U1 using Tapatalk
  13. ikeG

    Promaxx Heads - Thoughts?

    Linco diesel may have reman stock heads ready to go. Sent from my SM-G960U1 using Tapatalk
  14. ikeG

    Converter change

    Its never towed with this setup, and will not be able to until engines been repaired. I know there are now certainly better options than the 1058 for other applications. Hate to decide to try a different converter after engines back in but that may be what has to happen Sent from my...
  15. ikeG

    Converter change

    I got a guy that has had his needs change with his current LBZ. Its a S472/83/1.0 single truck with a stock cp3 and 40% nozzles. Built trans with a 1058. No towing needs until recently. He will occasionally need to move a piece of equipment short distances, gross trailer weight around 16k. The...
  16. ikeG

    4L60E diagnostic help

    I replaced the suspect tcm connector pin but no change. As soon as atf gets warm, it trips P2764. Pulled it back in, solenoid ohms out fine again. Checked it for a short to trans case with truck harness plugged into trans connector, bingo. Tcc pwm circuit was rubbed through on top of trans where...
  17. ikeG

    4L60E diagnostic help

    Solenoid ohms out at 10.5. I think I found a spread pin in the tcm connector. Waiting on a replacement. Sent from my SM-G960U1 using Tapatalk
  18. ikeG

    4L60E diagnostic help

    Test light stays lit with tcc on or off. That indicates bad tcm. But my snap on scantool only allows me to turn tcc on or off, no 0 to 100%. When I turn tcc on, duty pid goes to 99%. When I turn it off, duty goes to 0%. I can command tcc on while driving and it works. The circuits themselves ohm...
  19. ikeG

    4L60E diagnostic help

    Ok thanks mike Sent from my SM-G960U1 using Tapatalk
  20. ikeG

    4L60E diagnostic help

    Its a reman trans, 3k on it. 165k on the tcm. Once the trans is warm, it trips that code after clearing just sitting in the driveway. The reman trans company doesn't want to give me a solenoid and such until external circuits are ruled out. Which, using prodemand instructions, points to the...
Top Bottom