Search results

Search the forum Search Articles
  1. kidturbo

    -6AN Turbo Supply Mod

    Once welded up, cleaned up the inside with dremil and blew it out with some carb cleaner. Finished off with a special home anodizing kit... [emoji2] Sent from my SAMSUNG-SM-G870A using Tapatalk
  2. kidturbo

    -6AN Turbo Supply Mod

    Since I'm on a AN kick this week, decided to post this on up for review. Needed 2 turbo supply lines off block. Rather than pull off the oiling main ports with 4AN lines, I just modified the PPE remote filter adapters. Welded a -6AN bung to it, now not robbing a main bearing supply. Wasn't...
  3. kidturbo

    -8AN CP3 Pump Fittings

    After racking our brains on how to bend a hardline connecting the two rails around that Banks intake, I'd totally forgot about the inlet line clearance issue. Luckily that intake uses O-ring gaskets, so removing the upper half was a lot easier than I figured. I was gonna change the return...
  4. kidturbo

    -8AN CP3 Pump Fittings

    Here is a clearer close up pic I found for reference. Sent from my SAMSUNG-SM-G870A using Tapatalk
  5. kidturbo

    -8AN CP3 Pump Fittings

    Yeah 12mm X 1.5. Only conflict I can think of would be using with lb7 or lly upper thermostat housing might be close. Sent from my SAMSUNG-SM-G870A using Tapatalk
  6. kidturbo

    -8AN CP3 Pump Fittings

    They say necessity is the mother of invention, for this particular setup, that rings true. I searched a good bit for a stainless version to no avail. So if anyone finds something better please share. The port size is sufficient, and angle is what I needed to run the line down front of engine...
  7. kidturbo

    -8AN CP3 Pump Fittings

    Here is a couple pics of it installed. Takes a 18mm wrench (which I didn't have handy) and can be tilted about 15deg either side of vertical if needed. So far I don't see any disadvantages to it. Sent from my SAMSUNG-SM-G870A using Tapatalk
  8. kidturbo

    -8AN CP3 Pump Fittings

    Needed a way to not only increase line size feeding a 12mm stroker pump, but also change direction of the standard inlet to fit a custom intake. I had originally planned to harline into the fuel inlet. But that proved hopeless. After a little digging, I found where the pump threads are 12mm x...
  9. kidturbo

    VSS Input on Standalone LBZ/LMM

    Here is a couple from MAF signal testing with same generator. Sent from my SAMSUNG-SM-G870A using Tapatalk
  10. kidturbo

    VSS Input on Standalone LBZ/LMM

    Here is couple pics of bench testing speed range. I actually purchased this toy to test some MAF scaling, which it does perfectly also.[emoji2] Sent from my SAMSUNG-SM-G870A using Tapatalk
  11. kidturbo

    VSS Input on Standalone LBZ/LMM

    Did this one a while back on a LLY but had never tested on LBZ/LMM until tonight. The E35A/B series ECM will accept a single wire square wave pulse signal for vehicle speed just like the LB7/LLY. So you can use any GPS/acceleratometer or other pulse signal generator with square wave pattern in...
  12. kidturbo

    Cracked Piston solutions?

    Unisex... I like it. :hug: Don't forget to weigh that puppy.
  13. kidturbo

    Twins with Twins, Anyone?

    It's a drop box style unit with a 1:1 gear ratio. Sent from my SAMSUNG-SM-G870A using Tapatalk
  14. kidturbo

    Twins with Twins, Anyone?

    Also a big thanks to Ivan and the guys at FluidDamper for bringing me these new additions last week. All my other delays allowed them time to get their new neutral balance dampers into production before I was ready to spin one up.. Sent from my SAMSUNG-SM-G870A using Tapatalk
  15. kidturbo

    Twins with Twins, Anyone?

    Got pipes and turbos mocked up again, then started fitting the oil related parts. The cooler delete plate is about 2 inches to thick and screws with my cooler plans. Next time I'll tap the blocks for lines. But i did manage to bend the dipstick tube into submission. [emoji123] Sent from my...
  16. kidturbo

    Twins with Twins, Anyone?

    I know where there is a single ASD 8 for a deal.. Sent from my SAMSUNG-SM-G870A using Tapatalk
  17. kidturbo

    Twins with Twins, Anyone?

    Breaking my own rules Hawk.. Remember me saying avoid couplers near the turbo? Needed one non-rigid connection somewhere between exhaust side and intake. Cause somethings gotta have room to expand so not to stress the pipes. I'm using the best Vibrant boot they make, and kept tube gap to a...
  18. kidturbo

    Twins with Twins, Anyone?

    Nice. Where ya find that? Sent from my SAMSUNG-SM-G870A using Tapatalk
  19. kidturbo

    Twins with Twins, Anyone?

    A slight angle at the boot is a possible option I'm keeping open. The US sales rep for Shocker was in the area and stopped by Friday. He had one of their pressure side 4" units with him, which we mounted up for couple pics. A two piece design might also resolve the clearance issue by letting us...
  20. kidturbo

    Who else is going to UCC?

    Good job Mark. Just making it through all 3 events is something to be proud of. I was joking on the way out that a 4th event should be added, placing your truck onto a trailer end of day under own its power. [emoji2] Sent from my SAMSUNG-SM-G870A using Tapatalk
Top Bottom