Search results

Search the forum Search Articles
  1. OleBlackyLBZ

    What are you paying for Diesel in your area?

    We are still holding at 3.99/gas and 4.99/diesel here in western kentucky. I'm afraid it's going to just keep going up though.
  2. OleBlackyLBZ

    New or Re-Build Steering Box

    I need to take a closer look but from just a glance it seems to be coming out around the shaft on the bottom. My box is still good and tight though...
  3. OleBlackyLBZ

    New or Re-Build Steering Box

    I thought you could tighten one up really easily by just tightening a set screw.
  4. OleBlackyLBZ

    New or Re-Build Steering Box

    That PSC steering box looks tough, but I was hoping not to spend $700 lol
  5. OleBlackyLBZ

    New or Re-Build Steering Box

    I had a brain fart, it's the steering box I've been talking about not the pump.
  6. OleBlackyLBZ

    New or Re-Build Steering Box

    I just didn't know of there were other parts in there that would be worn out besides the seals with this many miles on it. If so I'd rather just replace the whole pump... if it's generally just the seals that go bad I'd like to try and re-build mine.
  7. OleBlackyLBZ

    What are you paying for Diesel in your area?

    Diesel is $4.49 here in Western KY. It was $3.79 I believe last weekend. No telling where its going from here, this is rediculous.
  8. OleBlackyLBZ

    New or Re-Build Steering Box

    My steering box is leaking. It has 287,000 miles on it, should I get a re-build kit for mine and replace all the seals? Or am I better off to just get a parts store replacement with a lifetime warranty. I have searched and searched and there dosent seem to be a good solution. Some even say...
  9. OleBlackyLBZ

    Is this Normal?

    I didn't think the tires were spinning and I don't think they are enough to feel anything, but apparently you are right.
  10. OleBlackyLBZ

    Is this Normal?

    I do have an Autocal. But I talked with Mark wal ago and he said it's normal, the tcm unlocks the converter as a failsafe when it sees the wheel speed jump suddenly.
  11. OleBlackyLBZ

    Is this Normal?

    Thanks, I don't have a way to log but I will try to figure something out. May just wait until I go back up to Mark's and let him look at it.
  12. OleBlackyLBZ

    Is this Normal?

    Thanks, I knew it had always done it and there were never any codes so I thought it might be normal.
  13. OleBlackyLBZ

    Is this Normal?

    There is no acceleration with cruise control on therefore it does not do it then. You have to have the pedal on the floor during acceleration for this to happen. Specifically racing
  14. OleBlackyLBZ

    Is this Normal?

    Cruise is fine, it's not under nearly enough load to do it then. Throttle burried on a 550+ hp tune it does it, but only when I hit a hard bump. It's like it pops out of gear for a second or two.
  15. OleBlackyLBZ

    Is this Normal?

    So I have noticed this for a long time and just assumed it was normal, now I'm not so sure. But when I'm accelerating hard on my bigger tunes and I hit a little bump like say where road meets bridge or something like that, anything that's enough to bounce the truck a little, the truck stops...
  16. OleBlackyLBZ

    Best compound set-up for 900+ hp

    He just purchased the pump and injectors so he will want to keep those. I think somethin like the stage 3 64 drop in from dans with the larger turbine wheel should handle what he is wantin to do and spool fast still. We just aint sure 485 vs 488.. leaning towards 485 since he is happy as long as...
  17. OleBlackyLBZ

    Best compound set-up for 900+ hp

    Just seen where Nick at Duramax Tuner's Duraburb makes 1050 with a 64 vvt drop in and sxe 488 on an lbz. Probably the route we will go! The 64 will be a fixed vane for a lb7 of course.
  18. OleBlackyLBZ

    Best compound set-up for 900+ hp

    I am posting this for a friend, he has a 04 lb7 that needs an engine re-build so he is going all out on a built motor. It's already in progress with wagler having just finished the machine work. He has a 12mm cp3 and will be running 100-150% injectors. Right now we are looking at a drop in 64...
  19. OleBlackyLBZ

    Broken Crankshaft Count?

    A friend of mine broke his crank a few days ago, it's a stock motor lbz around 700hp. He isn't a member on here if someone wants to add him to the list they can.
  20. OleBlackyLBZ

    best/ most comfortable winter work boot

    If money is no issue, probably a pair of Nicks or Whites customs. I want pair one day...
Top Bottom