Search results

Search the forum Search Articles
  1. kidturbo

    Twins with Twins, Anyone?

    Picked up injectors yesterday. Coating looks pretty good, but only time, fuel leaks, and salt water spray will tell. Coater cried about having to clean and tape each 3 times to make sure no sand got in. While for under $20 a stick I'm happy. Sent from my SM-G892A using Tapatalk
  2. kidturbo

    LML oil pump conversion info....

    That's what he said. Did it on the workbench. Took a few press tries on gear depth adjustment to get correct. But said it all lines up Sent from my SM-G892A using Tapatalk
  3. kidturbo

    Twins with Twins, Anyone?

    Stbd sealed up again. I'm heading home to go float on a pontoon boat with a 75hp outboard this weekend. Sent from my SM-G892A using Tapatalk
  4. kidturbo

    LML oil pump conversion info....

    Hey guys while i had the front cover off this week figured I'd share a pick of my LML pump conversion setup. This is on a medium duty pan, but clearance there is same as 4x4 truck. You can see where i cut the pump body and gear shaft to fit reluctor ring. A little trim on the pan edge and...
  5. kidturbo

    Twins with Twins, Anyone?

    Chatting with fingers the other day, he made a comment that makes me laugh every time I think about it. Said everytime he checks this thread he sees something new I've broken, but always relieved it's not his pistons... After 5yrs that's exactly how I view this floating R&D project. Wasn't...
  6. kidturbo

    Twins with Twins, Anyone?

    That's just in fuel system related parts... [emoji23] Your probably not to far off on hardware. Got 60 in 2 outdrives we just pulled off, and another 50 in the set going back on. Anyone wants to buy that first set highly discounted please step up.. Sent from my SM-G892A using Tapatalk
  7. kidturbo

    Twins with Twins, Anyone?

    Got the cover off, besides cam gear, no other issues found. Swapped that out, and after a little fishing, Ryan cam up with all but one of the missing teeth off the old pump gear. New CP3 and relief valves arrived today also.. What banjo fitting y'all running on these fancy valves? Sent from...
  8. kidturbo

    Twins with Twins, Anyone?

    Depends on how hot she's running. If it's just a little warm, got 2 of these baby units.
  9. kidturbo

    Twins with Twins, Anyone?

    A little over due, but got one of the two Novec 1230 bottles mounted up today. Dual mode, automatic and manual discharge. Now we can safely let it rip, like a Industrial Injection Engine... 🤪
  10. kidturbo

    Twins with Twins, Anyone?

    Dropped all 16 stick off today at the shop who did most of the other engine coatings. Decided to go with a 180F long bake coating. Was told key is in sand blasting the surfaces, which is also the main concern now. But gave him plenty of extra caps and stressed how important it is to NOT get any...
  11. kidturbo

    Twins with Twins, Anyone?

    It's the lo-bake type, 250F I believe. Temp was the main concern. I had Andrew at ID try it on a core. He just cleaned and disinfected all 15 sticks, and calibrated a new one to replace my screw up. So we weren't eager to bust em all apart again to go full bake style. Sent from my SM-G892A...
  12. kidturbo

    Twins with Twins, Anyone?

    Cerakote injector test. Tired of rusty injectors bodies mucking up my engines. Sent from my SM-G892A using Tapatalk
  13. kidturbo

    LMM code U0073?

    I knew there had to be a module back there somewhere. All this advice coming from a guy who's never owned a Duramax powered truck.. I have chop shopped a few however. LOL Here is my ECM power wiring diagram I've used for years. Noticed the D-BU Serial Data wire lists IGN on the ECM connector...
  14. kidturbo

    LMM code U0073?

    The second 120ohm terminator was in the chassis harness near the rear bumper on LBZ/LMM trucks.. I never could figure out why they put it back there. Guess some bus chassis or something had a CAN module towards rear axle. But once again, that shouldn't cause the code. In stand alone setups, I...
  15. kidturbo

    LMM code U0073?

    The ECM has 120 ohms terminator built in by default. The other one can be placed anywhere on the bus. Check across the CAN-HI and CAN-LO wires, you should read 60ohm or close to it. I don't think that's your problem however. I've played with that particular ECM on the bench more than anyone and...
  16. kidturbo

    Broken Crankshaft Count?

    Yeah main bearing was still in decent shape. Trashed the rod bearing was about it. First one I've seen caught half break before. Sent from my SM-G892A using Tapatalk
  17. kidturbo

    Broken Crankshaft Count?

    Saw this one couple days ago and had to share it. It knocked, wobbled, but had no movement when pry bar was used to check it. Well there's your problem.. Sent from my SM-G892A using Tapatalk
  18. kidturbo

    What did you do at work today?

    That was dang close to the drivers seat. I've seen a couple rogue tires break bad over the years also. Gives ya good respect for e=mc2. Glad to hear it was nothing old brown couldn't handle for ya. Sent from my SM-G892A using Tapatalk
  19. kidturbo

    Twins with Twins, Anyone?

    If you'd been in the shop, it sounded like gunfire every turn of the wrench.. I thought they were driving it off with a hammer... lol Sent from my SM-G892A using Tapatalk
  20. kidturbo

    Twins with Twins, Anyone?

    4ft breaker bar, and youth did the trick.. [emoji23] Sent from my SM-G892A using Tapatalk
Top Bottom