Search results

Search the forum Search Articles
  1. durallymax

    What is in this picture (piston bowl, stuck injector)

    There's little pieces in there that look like weld slag kind ofaybe ill snap a pic of them
  2. durallymax

    What is in this picture (piston bowl, stuck injector)

    well Im thinking about putting it back together, checking the compression. and if all is good, just run it.
  3. durallymax

    What is in this picture (piston bowl, stuck injector)

    Well our 03 farm truck had the #4 injector stick open just 10 miles after I put a new water pump in it. Went and bought a 2011 that day and it will be here tomorrow, but thats a different story. Anyways I wanted to check the piston out and see something weird. Im using my Snap-On 6000...
  4. durallymax

    working on a new writeup

    working on a new writeup
  5. durallymax

    Techangle=Huge Timer Saver

    Just tried using the 1/2" on a flywheel replacement im working on. Did the first 60* which happens to come out around 250lb-ft (kinda neat how it shows you the actual torque when you relax it). It consistently stopped me at 61 degrees everytime. Could be my slow reflexes. But I have noticed when...
  6. durallymax

    Just a little reminder

    ive forgot to take it out too, but it actually just held the motor and never broke.
  7. durallymax

    Swapping pinion yokes

    Vice versa obs to lmm
  8. durallymax

    Swapping pinion yokes

    Local shop says spicer doesn't make one to adapt 1480 to 1410 yet. so as far as swapping yokes I'm sure I need to check the thickness of each. But your saying I won't need a new nut or crush sleeve, or need to reset the pinion preload
  9. durallymax

    Swapping pinion yokes

    I like the conversion u joint idea, I'm gonna try that first then swap them if no luck Thanks
  10. durallymax

    Swapping pinion yokes

    Thats what im asking. What do I need to do for it. If its simply pop the old one off and put it onto the new/used one, then perfect. But im sure it is not. Reading through the manual its looking like Ill need a new nut, new crush sleeve/washer thing, and such. So that means waiting for parts...
  11. durallymax

    Swapping pinion yokes

    Just swapped a used rearend into a truck with a bad rear end, just swapped complete units to keep things simple (i though). However It skipped my brain that AL and Steel driveshafts have different u-joints I guess, and I either need to swap the pinion yokes or get a different driveshaft made...
  12. durallymax

    Dyno Explosion

    I know nothing about dynos really but know that over here in the midwest there are plenty of dynos that can handle immense amounts of torque from pulling tractor engines, which make quite a bit more than trucks for now.
  13. durallymax

    Dyno Explosion

    that tractor is a DT466 Block not a cummins. The original poster did not post it correctly. Dont know why, dont remember why, hence why the comments were disabled. If you look at it a little closer it becomes very obvious it is a 400 series block versus a cummins. Add to that the fact that...
  14. durallymax

    im done with this sh#$

    So he shoulda said he would be dissapointed to see him sell a broken truck to somebody who was assuming everything was kosher? Stuff like that ruins your reputation, fix it right and sell it right or tell the person whats up. Lets look at this another way. You want to rebuild your...
  15. durallymax

    im done with this sh#$

    then dont own an LB7 but then you can afford a newer one. Its a crapshoot. Buy a diesel jetta and park the truck. But their expensive too. Life sucks
  16. durallymax

    im done with this sh#$

    matched balanced set is key.
  17. durallymax

    Off Season Sled Pulling Mods

    4. Front of engine block can be no farther forward than 17” of the centerline of the front axle
  18. durallymax

    Off Season Sled Pulling Mods

    dodge boys will cry and break out their tape measures (if they knew how to count) and try to DQ you:D
  19. durallymax

    Off Season Sled Pulling Mods

    many places require motor to be mounted in factory location.
  20. durallymax

    Off Season Sled Pulling Mods

    Me nooo, like the products just not the cult that follows ownership (at least in my area its all :bow: to mother Deere. Plus the dealership service in our area isnt the best from our Deere ownership experiences, back down to only 2 things now though. 1560 Drill and 4x2 gator from 2000 that...
Top Bottom