LLY: paint94979's GT4094R to S475 turbo swap

paint94979

paint94979

Beer Nazi
Sep 18, 2006
11,715
8
38
37
ripmf666 said:
Hey Nick get me a pic of the exhaust wheel pic from back please
Click to expand...

Picture419.jpg
 
ripmf666

ripmf666

Active member
Sep 20, 2006
15,123
14
38
47
Wentzville Mo
Man that coati g and polishing turned out sweet I think I might have dome wood. I kinda miss my single now kinda twins and noload dynos don't mix well along with a up pipe leak lol:spit:
 
paint94979

paint94979

Beer Nazi
Sep 18, 2006
11,715
8
38
37
ripmf666 said:
Man that coati g and polishing turned out sweet I think I might have dome wood. I kinda miss my single now kinda twins and noload dynos don't mix well along with a up pipe leak lol:spit:
Click to expand...

ya i am very happy with the way the turbo turned out... thanks Henry:thumb:
 
gmduramax

gmduramax

Shits broke
Jun 12, 2008
4,077
250
83
Nor cal
I bet my stock charger, stock CP3 truck will still run faster than Nicks truck with his WD CP3 and huge S474
 
ripmf666

ripmf666

Active member
Sep 20, 2006
15,123
14
38
47
Wentzville Mo
Lol your truck is not 100% stock anymore with the built motor. Nick's turbo is not a S474 it's a S475sx. I watched a truck this weekend with a single wicked diesel cp3 and the new Garrett Gtx4202r lay down a good 720 had 820 rwhp on 2 or so pulls but had down shifts on the runs and still had alot of fuel left.
 
paint94979

paint94979

Beer Nazi
Sep 18, 2006
11,715
8
38
37
ripmf666 said:
When's the motor build
Click to expand...

Well after the 15th the truck will sit until it gets built. I'm gonna have Dmitri pull the motor strip it down to a short block and bring it down to Guy for a very mild build... key ways, cut and coat my existing pistons, carillo rods, new bearings, maybe stage 1 heads, and then balance the rotating assembly. Trying to keep it under 7,000$ we will see
 
0

03Dmax90

New member
Apr 28, 2010
74
0
0
paint94979 said:
Well after the 15th the truck will sit until it gets built. I'm gonna have Dmitri pull the motor strip it down to a short block and bring it down to Guy for a very mild build... key ways, cut and coat my existing pistons, carillo rods, new bearings, maybe stage 1 heads, and then balance the rotating assembly. Trying to keep it under 7,000$ we will see
Click to expand...

If its already out and getting built you might as well do it right the first time and go all out!!! :thumb:
 
paint94979

paint94979

Beer Nazi
Sep 18, 2006
11,715
8
38
37
03Dmax90 said:
If its already out and getting built you might as well do it right the first time and go all out!!! :thumb:
Click to expand...

I have yet to see where "going all out" has any advantages... I'm not going for record breaking times just a low 11 second truck that is fairly reliable. A cam is a waste for me as I am right at sea level so I don't need any help spooling, heads are also probably a waste but IMHO worth doing. After seeing what Dmitri did with his engines no need to go for overkill
 
duratothemax

duratothemax

<--- slippery roads
Aug 28, 2006
7,139
10
0
Wyoming
paint94979 said:
Well after the 15th the truck will sit until it gets built. I'm gonna have Dmitri pull the motor strip it down to a short block and bring it down to Guy for a very mild build... key ways, cut and coat my existing pistons, carillo rods, new bearings, maybe stage 1 heads, and then balance the rotating assembly. Trying to keep it under 7,000$ we will see
Click to expand...

with assembly and motor R&R???????????? Or $7,000 in parts.
 
You must log in or register to reply here.
Top Bottom