Sounds like fun Tony congrats should be a fun year for you next year what are you going to run OSTPA, NTPA, PPL? And does this mean that the HOOKER is sold now? If so where is it going to?
Off Season Sled Pulling Mods
- Thread starter Rhall
- Start date
Think they said Hooker 2 went to IN?? or maybe it was OH?
Is the mod truck going to be out next season Tony???
That's bound to be a schit ton to get done between now and then if so!!!
Is the mod truck going to be out next season Tony???
That's bound to be a schit ton to get done between now and then if so!!!
Tony Burkhard
Allseason Diesel Per.
The DH 2.0 was sold to a puller in Indiana. DH 3.0 will be out as soon as i get it done and none sooner.. LOL I will pull it at as many pulls as i can make it too. It might be a late start with the new truck.
Tony Burkhard
Allseason Diesel Per.
I built the last truck in nine months from ground up but this one will have new challenges. First year will be a learning curve thats for sure. Already looking at up-grades for two years down the road. I would love to pull it next year but time will tell.Think they said Hooker 2 went to IN?? or maybe it was OH?
Is the mod truck going to be out next season Tony???
Tony Burkhard
Allseason Diesel Per.
Guess this would be a good place to ask since all the subscribers, but had anyone messed around with cantilevers on their hitch? Or is this deemed trick hitch?
---
I am here: http://maps.google.com/maps?ll=38.757114,-92.807359
2011 Ferd F-teenthousand
Sent from my iPhone using Tapatalk
---
I am here: http://maps.google.com/maps?ll=38.757114,-92.807359
2011 Ferd F-teenthousand
Sent from my iPhone using Tapatalk
Well so far just hitch height and hook point has to be the furthest rear point on vehicle and bracing can't extend past front of rear axle
---
I am here: http://maps.google.com/maps?ll=38.764150,-92.466905
2011 Ferd F-teenthousand
Sent from my iPhone using Tapatalk
---
I am here: http://maps.google.com/maps?ll=38.764150,-92.466905
2011 Ferd F-teenthousand
Sent from my iPhone using Tapatalk
Sump showed up, heads are back out getting a tad more loving, cam and fluidamper are in route. Ready to get this engine and Trans out and get to work. Been considering a pump and turbo change as well. Roll pan should be getting painted this week as well
Heads are back on. Heading that way in about 5 minutes to start buttoning it up to get it back between the frame rails soon.
lucky you,, I'm heading to the shop to try and get a pump gear off an 06 CR that exploded the cp3 on me last week. Damn gear spun and is stuck on the shaft now. really hope i dont have to pull the front cover and cut it off
lucky you,, I'm heading to the shop to try and get a pump gear off an 06 CR that exploded the cp3 on me last week. Damn gear spun and is stuck on the shaft now. really hope i dont have to pull the front cover and cut it off
If you've read anything on this site about me and my pulling trucks, lucky is not a word generally used. :roflmao:
Hahaha gotta be better then my luck this year
I was test driving this dodge after some turbo work, valve springs, studs, injectors, and updating the smarty and messing with the tuning,,,, made it 5 miles and the pump shits its guts everywhere. thank god I didn't have to cut the gear off and and pretty new 6.7 pump is on it and it made it back to IL fine
I was test driving this dodge after some turbo work, valve springs, studs, injectors, and updating the smarty and messing with the tuning,,,, made it 5 miles and the pump shits its guts everywhere. thank god I didn't have to cut the gear off and and pretty new 6.7 pump is on it and it made it back to IL fine