My LLY Engine Build

b_r_a_d_79

New member
Aug 3, 2013
183
0
0
KY
Your truck looks sick!
Schematics? Who's cam is it?
I think you just have to know the stock and new firing order and move a couple injector wires in the harness accordingly?

Here's a question I had a while back and never asked...
If you're running a balanced set of injectors, numbered for the cylinder, and swap to an alternate firing cam, don't you have to move the physical injector to the new hole, as well?

It's socals cam

I couldn't answer your question about the balanced injectors.
 

b_r_a_d_79

New member
Aug 3, 2013
183
0
0
KY
Well the sdp intake I had didn't clear the cp3 high pressure line so I had to fab something up and couldn't find any bends sharp enough. Had to resort to the pie method. Going to powder coater tomorrow.
 

Attachments

  • image.jpg
    image.jpg
    88.8 KB · Views: 46

moparkxracer

Well-known member
Jun 25, 2010
2,309
33
48
Out and about
Call Socal he will email pictures of what needs to be done.

Does anyone know what size belt is being ran with the triple cp3 kits? I measured 147 but the longest belt I can find is 142. Also does anyone have the schematics for the wiring change for the alternate firing cam?
 

b_r_a_d_79

New member
Aug 3, 2013
183
0
0
KY
Wrapped pretty much everything up today. Have a fuel leak to trace out and I have an issue with the trains that seems to be electrical. Also waiting on my new ppei tunes.
 

Attachments

  • image.jpg
    image.jpg
    132.8 KB · Views: 61

b_r_a_d_79

New member
Aug 3, 2013
183
0
0
KY
Will do. May try to make some easy pulls on the dyno to test everything before pushing it on the street.
 

Stancedlb7

Cummin Stroke this Duramax
Feb 9, 2015
649
0
0
SLC, UTAH
I'm curious why you went 83 over the 75 instead of going larger? I'm just under the impression that the 83 would choke the 75.
 

b_r_a_d_79

New member
Aug 3, 2013
183
0
0
KY
I'm guessing some of you are seeing my signature thinking that's the turbo I'm currently running. The signature is not updated. I was running a 83 before the engine build. The fleece s475 is a 87.
 

b_r_a_d_79

New member
Aug 3, 2013
183
0
0
KY
Ok I'm having some electrical issues and would like to know if someone else has ran into similar issues. I feel like i just looking over something simple but I am running out of ideas.The transmission is not properly operating and I have codes P0743, P0748, P0763, P0768, P0773, P0778, P0841, P0848, P0875, P0876, P0880, P2810.
Also something else i noticed while scanning the truck is all balance rates are stuck at 0 and do not move.
 

Stancedlb7

Cummin Stroke this Duramax
Feb 9, 2015
649
0
0
SLC, UTAH
I'm guessing some of you are seeing my signature thinking that's the turbo I'm currently running. The signature is not updated. I was running a 83 before the engine build. The fleece s475 is a 87.

Yaah I read your Sig. Lol x2 on a vid. Sorry I'm no help with the issue.
 

b_r_a_d_79

New member
Aug 3, 2013
183
0
0
KY
It's always something with this truck. The front pump seal when out and started pouring trains fluid out of the bell housing during test drive.
 

Attachments

  • image.jpg
    image.jpg
    190.8 KB · Views: 39