Allison Help

[kx500]

I was cooking down the road, passing some cars. Transmission slammed into 3rd gear and the check engine light came on. It gave me a P0700 code, how do I fix that?

 

[Akdiesel]

Build it or take it easy on the 4-5 shift and 5-4 shift. fill out your signature with your truck and what's done to it. You limped the trans btw

 

[kx500]

Some times in the morning when it's cold out the p0700 code will pop up when I start the truck.

 

[kx500]

Build it or take it easy on the 4-5 shift and 5-4 shift. fill out your signature with your truck and what's done to it. You limped the trans btw

so which part is failing?

 

[custom8726]

C3 clutch slipping on the 4-5 shift,, What tuner/programer are you using?

 

[kx500]

C3 clutch slipping on the 4-5 shift,, What tuner/programer are you using?

45hp over stock

 

[Sledhead]

Build it or take it easy on the 4-5 shift and 5-4 shift. fill out your signature with your truck and what's done to it. You limped the trans btw

More info would help us help you.

 

[Chevmeister]

Bawhahaha, welcome to the club. If your getting a p0700 that's a generic code for the trans being pissed. Limp can be reset with a few ignition cycles. If you get it often save some coin, trans build will cost 3-4 grand depending on what you use. Parts can be had cheaper if you can build it yourself.

 

[CumminStrokeThisDURAMAX]

i hate it when that happens. happens to me alot i just gotta save money for a ppe stage 5 trans kit

 

[Big Block 88]

I don't understand how this is happening to people. I have run some very large tunes McRat's race tune being the biggest, with a completely stock allison 6 speed and only limped one time. But then again I lift for the higher shifts let it shirt and roll back into it.

 

[SteveFord]

I don't understand how this is happening to people. I have run some very large tunes McRat's race tune being the biggest, with a completely stock allison 6 speed and only limped one time. But then again I lift for the higher shifts let it shirt and roll back into it.

5 speeds won't hold as much as the 6 speeds in stock form. I know of few guys with 6 speeds that ran a lot of power through them stock and never limped. When tore down the clutches were junk and steels warped but never limped.

 

[Colt]

Didn't Maxdout run with stock tranny racing with hard tuning? Seems like I read a long thread about Rob? and ? doing that as they were amazed how much it did take. I think they built it though later. 6 spd. must hold good for it's torture time Power just takes it apart with time. Guess that's why Mike and others who build em' up then keep it tickin'.

 

[Sledhead]

I've got a hunch what's causing mine to do it...

 

[intropiles]

I was cooking down the road, passing some cars. Transmission slammed into 3rd gear and the check engine light came on. It gave me a P0700 code, how do I fix that?

I had the same issue it was the start of a PIA..


Edit :witch:

 

[MMLMM]

I was cooking down the road, passing some cars. Transmission slammed into 3rd gear and the check engine light came on. It gave me a P0700 code, how do I fix that?

spam!!!!!!!!!!!

 

[MACKIN]

I had the same issue it was the start of a PIA

Whats up with pimping the link ?

 

[MACKIN]

spam!!!!!!!!!!!

Seen that to did ya :rofl:

 

[MMLMM]

Seen that to did ya :rofl:

Lol, I just happened to run my mouse over it. Is this guy legit, or a spammer???

Whats spammer posts tech :rofl:

 

[kx500]

What is the cheapest route? what kit should I use? I don't race or pull.
can I get a way with a shift kit and converter?

 

[Kat]

I had the same issue it was the start of a PIA

Please don't link to other sites thanks :thumb: