475 compressor housing to cold pipe o-ring

[Chevy1925]

So where would i order one and what does it look like lol.

i definitly feel dumb for the fact i had a good feeling there was suppose to be some sort of gasket between my s475 and the cold pipe v-band but never put one in it nor had had one with the kit. Only reason i decided now i need one is i figured id do a pressure test on the intercooler and piping to check for leaks since i was only gettin 45psi on the big tune. Well, after hearing and feeling a huge woosh of air, i think i found it lol. then after talking with ruben and another buddy of mine, i was informed, there SHOULD BE an o-ring in there. lol

And yes, ive been running it this way even when i bent the rods . huge blonde moment :roflmao:. May the jokes start......

 

[BLKLMM]

Trent should have one:thumb:

 

[paint94979]

i got mine from ATS but yes trent will have one

 

[hondarider552]

:spit::rofl::rofl:


Send me pic of said O ring location on 475 James

 

[BLKLMM]

Stfu with your purple shit that's why u are slow bitch:roflmao:

 

[paint94979]

You see the inner notch? That is where the oring goes... This is a pressure tester Trent made me.

Sent from my PC36100 using Tapatalk

 

[Chevy1925]

:spit::rofl::rofl:


Send me pic of said O ring location on 475 James

Its between the compressor housing amd the cold pipe. That v-band that holds both together there is suppose to be an o-ring i guess. I dont see a groove but then again, i dunno what kind of o-ring goes thwre (round, square, sheethed type, ect).

 

[hondarider552]

If there isnt a grove, I dont think a O-ring goes der

 

[Chevy1925]

Let me go yank the pipe of real quick. I dont remember seeing any groove

 

[BLKLMM]

If there isn't then use rtv like I said b4:thumb:

 

[paint94979]

If there isn't then use rtv like I said b4:thumb:

James if i have learned anything over the years it's to not listen to this guy... his truck has a built engine, slicks, big injectors, and lots of air and still runs mid 11's My truck will run with his faggot LMM

 

[Chevy1925]

If there isn't then use rtv like I said b4:thumb:

I dont see it holdin ruben for as much air that was rushing out of it. Maybe i need a new
v-band clamp too?

James if i have learned anything over the years it's to not listen to this guy... his truck has a built engine, slicks, big injectors, and lots of air and still runs mid 11's My truck will run with his faggot LMM

Lmao


Here is some pics

 

[hondarider552]

IDK about a O ring but can I please wash your engine bay for you

 

[Chevy1925]

IDK about a O ring but can I please wash your engine bay for you

Not something one man says to another brian lol.

Shes gettin a bath after shes fixed

 

[paint94979]

you're going to need a new flange and or cold side pipe.

 

[Chevy1925]

Guess ill be on the phone with trent tomorrow. He had to have had it sealed some way. Maybe, just maybe there is a groove on the cold pipe under the powdercoat

 

[BLKLMM]

James if i have learned anything over the years it's to not listen to this guy... his truck has a built engine, slicks, big injectors, and lots of air and still runs mid 11's My truck will run with his faggot LMM

Oh really...when is that? Your bucket will never run:roflmao::roflmao: you are still, and always be slow:thumb::coolspot:

Try the rtv and if not send pipe to Trent and he will make a new one with the flange that has an o ring:thumb:

 

[paint94979]

im mentally slow Ruben but my truck is kinda quick

 

[BLKLMM]

:spit: OK...pinche wuerro...I assume with the ladies too huh:hug:

 

[paint94979]

my girlfriend has a different opinion ahahha