Search results

Search the forum Search Articles
  1. RIDMAX

    U1301 code question

    Having a problem with a recurring u 1301 code. I had the bed and bumpers off my truck the past week and a half to paint them. Put everything back together this weekend, cleaned the truck and lightly sprayed down the engine compartment avoiding electronics as much as possible. Ran the truck that...
    • RIDMAX
    • Thread
    • Replies: 0
    • Forum: LBZ
  2. RIDMAX

    Brake problems

    Didn't throw any code for me or no code I could read with my autocal.
  3. RIDMAX

    Brake problems

    My truck was doing the same thing. Found out it was the low speed abs sensor that was bad. Replaced the quick disconnect pigtail that attaches to the wheel bearing hub assembly and fixed it. The other thing you might be able to do is unscrew the end that threads into the hub assembly and...
  4. RIDMAX

    Cv axle replacement question

    Found a napa that was open and switched out the shaft for the correct one. They didn't have an explanation why it would have had the same part number but different design. Maybe boxed wrong or different year shaft who knows.
  5. RIDMAX

    Cv axle replacement question

    That's kinda what I thought I just want to make sure they are indeed the same or maybe have them get another factory style shaft and switch the odd one out. Too bad it's Sunday and they aren't open
  6. RIDMAX

    Cv axle replacement question

    They should both be the same that's why it's odd. They both measure the same and seem to fit the same yet they have different hub ends don't get it
  7. RIDMAX

    Cv axle replacement question

    Odd ball cv
  8. RIDMAX

    Cv axle replacement question

    Replaced the cv axles today in my 07 classic. Job went smooth until I got everything back together and went to double check I torqued everything and noticed that the hub end of the cv axles are different not the passenger side vs the drivers side. I didn't notice it when I installed them since...
  9. RIDMAX

    LMM: New guy from RI

    What time does the dyno day start would like to check it out
  10. RIDMAX

    LMM: New guy from RI

    Truck looks good where in ri?
  11. RIDMAX

    Help: Pulsing brake pedal 2002

    I'm having the same problem as the op. only happens right before the truck stops feels like the brakes lose pressure for a second,brake pedal pulses then goes back to normal. Checked power steering fluid it was fine I guess I'll have to check the low speed abs sensors I just replaced the...
  12. RIDMAX

    h2 wheels on duramax

    Stock Chevy/gmc alloy center caps fit without trimming steel wheel center caps need to be trimmed to fit
  13. RIDMAX

    Random loss of prime

    Possible wif sensor on filter loose or cracked? Had similar problem would lose prime after sitting overnight
  14. RIDMAX

    New shop

    definetely wanna beef up that ridge to carry the roof load and keep the ridge from sagging and bowing the walls especially without using collar ties. It also doesn't look like you cut a birds mouth (notch) in the rafters where they meet the exterior walls which locks the rafters to the top plate...
  15. RIDMAX

    congrats to richLMM

    Just wanted to congratulate richLMM for making it into the readers diesels section of diesel power magazine. Just got the issue today nice pic.
  16. RIDMAX

    hello from rhode island

    Trucks looking mean as always
  17. RIDMAX

    cutting a hole for a stack

    5 or 6" hole saw depending on the size of your stack/system. Typically hole saw is around $40 and the arbor, which is the pilot bit and mount for the hole saw, is around $20. This setup will make the cleanest cut and you can keep the piece you cut out for replacement later on if necessary
  18. RIDMAX

    Should I color match my front?

    I'd keep the grill and bumper chrome, ties in the chrome wheels and the stacks
Top Bottom