Search results

Search the forum Search Articles
  1. 1SloLMM

    Rear suspension setup

    I'm still in progress but I only have 2 leafs, mcgaughys hangers, Caltrans and 3 inch shackles. I bought viking shocks and couldnt get them to work with the stock mounts so I just completely redid it all to get the shocks vertical and used adjustable coil over mounts on the axel. In the lowest...
  2. 1SloLMM

    Lift pump, Delete stock fuel filter?

    Run the provided line up to the quick connect or straight to the cp3 also. If straight to the cp3, i went from half to 3/8 with fittings (not a splice) so it could still be bled close
  3. 1SloLMM

    no fuel pressure at the bleed screw

    If you can hear the pump, reprime it and see if it gets to the housing.
  4. 1SloLMM

    UCC results and discussion

    I don't know what Baca runs for trannys usually I think he would of been in the same situation as last year if he didn't break the tranny he made the night before. He said he had to use Randys out of his race truck and hated that he had to go back to a 48. Husker is local to me and I try to...
  5. 1SloLMM

    What did you pay?

    Drove the 17 a couple nights ago. Was way less than I was expecting. Seems they didn't care to try much on the interior, motor was surprising noisy, cab didn't seem to keep much road noise out, and hardly any rear leg room if you're probably anything over 6ft tall up front. I don't know if...
  6. 1SloLMM

    What did you pay?

    I plan to look into the 1500 duramax a couple years down the road. I bet they will be in 60k or above so I might wait out a used one I could tune alright away. I have a new 2017 1500 but terrible mileage even with the 10 speed. I wanted to stay in a half to be able to pull my truck to anything...
  7. 1SloLMM

    What did you pay?

    Looking into getting one. How much have you all been paying out the door? Right now locally they have a 17 loaded for 43980 sticker and said they would knock it down to 39000, or an 18 for 41615 stick they would knock down to 38315. Have they had and incentives at all for these recently?
  8. 1SloLMM

    Trans Crossmembers

    Is anyone making them yet? I would like to have one before spring if possible!
  9. 1SloLMM

    New setup is done

    The webbing is a little weaker in block is all. If that block is close enough just go and feel any grooves. Doesn't look like it cracked out so unless it melted through to the outside it should be fine I would think.
  10. 1SloLMM

    What does everyone buy these days for good tie Rods , idler ,& pitman?

    I bought rare parts. There's bundles on eBay if vendors don't have it
  11. 1SloLMM

    Rear set up

    Thanks for all the suggestions. I believe I will be getting the artec box since they make the correct size. Another topic I can't find much on, weight (for 4x4 atleast), since the front of these trucks are so heavy how much does it help to move weight back? Is it most effective to move it as...
  12. 1SloLMM

    Rear set up

    Anyone know of a hefty frame mount battery Box? I'd like to get everything out of the bed. Needs to be strong because I switch to a single diehard platinum marine battery. It's a group 31 and weights about 75 pounds I believe
  13. 1SloLMM

    Rear set up

    Thanks OregonDMAX I'll have to look into the rules more. The way it's looking though I don't know if it will ever get out of the garage again. I'm looking at having Rhodes race cars make one up for me. I wanted to buy their 69 camaro tank and try to have a behind the license plate filler but...
  14. 1SloLMM

    Rear set up

    I made them out of 3/4 so no one could look at it and think it weakened the frame if i ever had to sell it. I made them a little deeper then I probably need as I couldn't even get the axle to touch the notch fully compressed with ratchet straps and maxing out the caltracs. I'll probably be...
  15. 1SloLMM

    Rear set up

    Just wanted to make sure the pictures worked. Here's the other part for any problems. The wood represents a fuel cell ill be having made, and im considering notching out the bracket holding the FASS so i can raise it up a bit more and get it in closer to the tubing.
  16. 1SloLMM

    Rear set up

    Well to bring this back up, this probably one month project turned almost a year now. heres some updated pictures. Anyone see any problems that could arise? First I'll just share a couple of the notches i did:
  17. 1SloLMM

    Trailer wiring

    Got it all figured out. The Only thing that's really a pain is having to undo all the conduit all the way up to the fuse box. They are all separate and you will need a long pin out tool for the fuse box as on its right next to the relay.
  18. 1SloLMM

    Trailer wiring

    Looking to remove the wiring for the trailer. I've gotten it all the way up to under the DS door and I was just wondering if it goes all the way to the fuse box and are there and wires spliced together at the ends or do they stay individual the whole time for the blinkers and brake lights?
  19. 1SloLMM

    Stuff to do around Phoenix

    We take off next Wed early. We just got back from driving around the valley and some of downtown Scottsdale. Can't believe how different and nice everything is around here. Finding a lot of cool places just blindly driving. Seems like teslas, Mercedes, porches, and maseratis are the norm for...
  20. 1SloLMM

    Stuff to do around Phoenix

    We are at the scottsdale plaza resort. We may switch hotels to get closer to mesa but its pretty nice over here. We came down here without a plan essentially because I knew it wouldn't be that busy being summertime. Golfing is out. Haven't done it in years and no one I'm with wants to either...
Top Bottom