Search results

Search the forum Search Articles
  1. catman3126

    LML LML DTC's not visible in Canada

    use Revo uninstall and then do it.
  2. catman3126

    What does everyone buy these days for good tie Rods , idler ,& pitman?

    rare parts worked for me with slicks and launched a 10 second pass with a solid center link
  3. catman3126

    P0841-p0846

    O-rings are fine, whole trans was swapped in with a valve body change also. when I check continuity tot eh two pins to ground its not constant it just beeps intermittently, where as is supposed to give a constant tone for continuity. maybe a ground issue. had to move it off the lift for another...
  4. catman3126

    P0841-p0846

    Well it had power to the pins like it should. there was only 4 in the connector on this year there is not pin at # my book said it was the gray connector so now what?
  5. catman3126

    P0841-p0846

    I'm getting these two codes shortly after the truck is started and rand for 10 seconds, changed the pressure with with a known good one out of my running 03' seems to only have 5th gear as it will roll 70 on the lift with out shifting and no reverse. Called yah mike no reply yet. this is a valve...
  6. catman3126

    Efi Dealers

    But here we go again Sean whatcha getting at with your comment? it has no validity to this thread other then you cutting me down :thumb:
  7. catman3126

    Efi Dealers

    Dealers for other tuners yes but not an actual EFI Live dealer. they are just selling the big name tuners tuning. I have quite a few shops across the country selling my tuning same as the big guys but not on the big scale of things.
  8. catman3126

    Efi Dealers

    My shop is the only EFI Live dealer in Oregon and does in house tuning, meaning writing the tunes and not selling others tuning. Like most say stock setups are most common and most, LML's are the most common these days and so far have only been stock setups except a few fixed vane trucks. I do a...
  9. catman3126

    Service 4wd and a new t case/encoder motor

    Lmao eat a dick. I got it all fixed up and back to the customer. It was the shit batteries keeping it from doing the learn.
  10. catman3126

    Service 4wd and a new t case/encoder motor

    well I think I just messed up lol. I found online where it says to put the t case in neutral, I swapped encoder motors off the old t case just in case the new one would only work with the updated programming I've been reading about and since I don't have a way to put the encoder motor to the...
  11. catman3126

    Lb7 build

    yep mine is totally streetable w/3200 stall when need and lockup is awesome.
  12. catman3126

    Service 4wd and a new t case/encoder motor

    Ok so a customer brought an 08 lmm dually C@C to my shop and wanted a new t case put in. he had it troubleshot somewhere and they said it was bad I messed with it and it wouldn't go into 4 wd so I put a new one in at his request yesterday. when I tested it it seemed t be in neutral and wouldn't...
  13. catman3126

    Lb7 build

    Just got there myself, going to see if I can makes 9's next year.
  14. catman3126

    Lb7 build

    Oh shit get that thing up over 3k lol. I like my 3200 suncoast. shits get pretty wild launching at 3200, I think mine will even let me go too 3400 when the big charger really comes on.
  15. catman3126

    Lb7 build

    What convertor do you have? what stall are you going to go with?
  16. catman3126

    Going for tens in the zf. (Mission Accomplished!!!)

    Slicks made a night and day difference on mine as did the straight center link.
  17. catman3126

    Allison 5sp: Issues after rebuild

    Did it shift and drive fine before you took it apart?
  18. catman3126

    Allison 5sp: Issues after rebuild

    Oil level good when Idling? Codes? sump filter didn't fall out when you put the pan back up did it?
  19. catman3126

    Engine build

    I may if needed.
  20. catman3126

    Engine build

    I was just gonna say. ehhh its in my sig lmao.
Top Bottom