Search results

Search the forum Search Articles
  1. ikeG

    Yukon 30 spline axles any good?

    Dual splined, which I think you're referring to as 'puck style,' will be substantially stronger​ than single splined. Even if their the same material.
  2. ikeG

    Fastest single VGT

    Did someone say progression?? Sent from my XT1585 using Tapatalk
  3. ikeG

    Help with engine build

    We ran a bd flexplate in our last engine to meet sfi requirements at 1000-1100 fwhp for few years and it's still going strong for the guy I sold it too. Sent from my XT1585 using Tapatalk
  4. ikeG

    Help with engine build

    Say huh? Where at? Sent from my XT1585 using Tapatalk
  5. ikeG

    Help with engine build

    $375 Sent from my XT1585 using Tapatalk
  6. ikeG

    Help with engine build

    Put a bd flexplate on it if you're concerned. Sent from my XT1585 using Tapatalk
  7. ikeG

    Help with engine build

    Just get merchant pushrods. No need for rerod-strong ones. You do not need a billet flywheel.
  8. ikeG

    manual trans diesel record "build"

    Wish you all​ the luck.... But I think it's going to be tougher than you act like it will be. The original record set by Caleb was with a 'budget' built motor by today's standards. He obviously could row some gears! That record took forever to break and when Dirk did, with the same truck, it...
  9. ikeG

    Lbz fuel pressure sensor data

    Update?
    • ikeG
    • Post #22
    • Forum: LBZ
  10. ikeG

    Strange EFIlive error

    Like was mentioned, even though the update checker says you have latest, the tuner is using beta software if available, so you will have to update to it from the forum
  11. ikeG

    Question: Ordered Wheels, TPMS?

    Yes. Deal with them almost 6 days a week at work Sent from my XT1585 using Tapatalk
  12. ikeG

    Question: Ordered Wheels, TPMS?

    I have only had good luck with oem sensors.
  13. ikeG

    trouble shooting

    I'll second the spek gauges. Super high quality​, look great, and have recalls plus hi & lo limit warnings. Have been using them for years on many trucks.
  14. ikeG

    Removing wiring

    The 8 individual glow plug wires with the eyelet per glow plug are what I was referring to. I can't remember where the wires for gpcm originate. Sent from my XT1585 using Tapatalk
  15. ikeG

    Seriously?

    Been quiet here lately.... 6L90 sump filter Sent from my XT1585 using Tapatalk
  16. ikeG

    Removing wiring

    Glow plugs go to the two connectors Sent from my XT1585 using Tapatalk
  17. ikeG

    Removing wiring

    The engine harness is separate from the other harnesses. It connects to the truck side at the two bale connectors on the driver's side of the engine. In order to remove the wires, you would have to unwrap the plastic conduit and tape, which would allow you to remove that wire and then you...
  18. ikeG

    LML Lgh in a lml. Cranks but won't start

    If the fuel system was completely drained it will take quite some time cranking to start. Check all supply lines. Make sure fuel filter lines aren't crossed. Just going to have to go over everything associated with the fuel system Sent from my XT1585 using Tapatalk
    • ikeG
    • Post #12
    • Forum: LML
  19. ikeG

    LML Lgh in a lml. Cranks but won't start

    But if the sensor says 0 rp that's where u need to start. Sent from my XT1585 using Tapatalk
    • ikeG
    • Post #10
    • Forum: LML
  20. ikeG

    Cracked Piston solutions?

    I'm fixing a LML that rolled in here this week that has one piston skunked. It needs honed and hopefully can stay standard size bore Sent from my XT1585 using Tapatalk
Top Bottom