Search results

  1. SoCalMike

    Axle Dump Exhaust

    It will have a deeper tone.
  2. SoCalMike

    *****stolen truck from my shop*****

    Glad to hear Nate
  3. SoCalMike

    *****stolen truck from my shop*****

    No problem man
  4. SoCalMike

    *****stolen truck from my shop*****

    I will keep an eye out for it if it's around my location. What city was it stolen from?
  5. SoCalMike

    LBZ: Tensioner & pulley replacement

    There are two 18mm bolts on the engine that hold the fan shroud. They are on the passenger side engine. Remove those and the 13mm (I think its 13mm) bolt by the oil fill cap and you can move it out the way just enough. Just make sure the rubber gasket thing that goes around the fan shroud is...
  6. SoCalMike

    Heatwave Phoenix

    A few years ago I was driving from Cali to Phoenix, and it was 118f in the middle of the desert at 11pm......
  7. SoCalMike

    Heatwave Phoenix

    Must have been hot there today. I remember when you built my trans and I was at the shop. It was about 90/95 outside but your shop was still cool. It was about 85 at my job in Huntington Beach today. Was not bad at all. But we are pretty close to the beach.
  8. SoCalMike

    "OFFICIAL" What did you do to your D-Max today?

    I am at stock height and they fit fine. Cut the wheel well liner a little and pulled back the ebreak cable. The +18 offset helps. No rubbing at all. I have ran it lower than stock height also with no rubbing too.
  9. SoCalMike

    "OFFICIAL" What did you do to your D-Max today?

    That sucks Brock. Sorry man....
  10. SoCalMike

    "OFFICIAL" What did you do to your D-Max today?

    Nice Brock. You will like that setup.
  11. SoCalMike

    Happy Birthday Hondarider 552

    Happy birthday Brian!
  12. SoCalMike

    Happy Birthday Mike L

    Happy birthday Mike!
  13. SoCalMike

    P0777

    I would turn it down and call Mike L to discuss your options
  14. SoCalMike

    Rare parts

    I have the g2's and had the old style. The g2's are bigger. And they won't pinch the boot at full drop out on the spindle side like the old rp tierods. One zerk is on the tierods itself (spindle side) and the other is on the stock centerlink on my truck. So no need for two fittings on the...
  15. SoCalMike

    04.5 LLY Built Suncoast Running Hot?

    At 175f (transmission temperature) the fluid level should be at the middle of the lower hot hash mark. This is what my builder has told me. I just make sure at operating temp or as close as I can get it to 175f, the fluid level is in the middle of the "hot" section of the dipstick.
  16. SoCalMike

    04.5 LLY Built Suncoast Running Hot?

    If you run dex3, at 240/250f the additives will break down and the fluid will be trash..
  17. SoCalMike

    LBZ: Caution: LBZ Coolant Leak Hazard!

    Mine had no damage. When I first got the truck I notice it and turned the clamp toward the engine bay. I forgot i did that. Couple days ago I just removed the clamp.
  18. SoCalMike

    Inglewood Transmission

    It's always a good time hanging out with Mike and his crew.
  19. SoCalMike

    My Country Boy Limo. 06 LBZ

    Looks good buddy!
  20. SoCalMike

    LBZ: Caution: LBZ Coolant Leak Hazard!

    I am going to check mine and remove the clip like suggested.