Search results

Search the forum Search Articles
  1. kidturbo

    How To: LMM OS - MAP Scaling

    Actually it's 14.5 psi to 1-bar, or 100kpa. According to my unit converter app.. :)
  2. kidturbo

    How To: LMM OS - MAP Scaling

    Best I recall. I know for certain the ECM uses KPA values in the code, and when you read map2 with key on engine off, OEM sensors read mid 90's in my neighborhood, or about same as BARO..
  3. kidturbo

    How To: LMM OS - MAP Scaling

    Glad to see someone else putting in hours on this one, I'm wiring up a couple 10 bar MAP setups this week.. It's been a couple years since I last set down at the table to hashed this out the first time. So please forgive me if I don't seem to recall much detail. But here is what I know about...
  4. kidturbo

    Seriously?

    Man hate to hear that. Timing and time, does it every time...
  5. kidturbo

    Twins with Twins, Anyone?

    Ya hit the button beside it that says Oh-F... Co2 bath. Without running a cable there is no 99% failsafe. However electrical latch release is industrial standard on oil gas equipment. So I'm good with it for now. Sent from my SAMSUNG-SM-G890A using Tapatalk
  6. kidturbo

    Twins with Twins, Anyone?

    I stole the bearings and seals outa the TB. Shaft clearance not an issue now either. If theses corode or stick, ya got bigger issues. Cycling them not an issue, but someone's gonna have to walk between engines and reset them every time. They will be spring loaded with a 12v latching...
  7. kidturbo

    Twins with Twins, Anyone?

    Throttle blade plates are back. Lot of work for something you hope to never use. Sent from my SAMSUNG-SM-G890A using Tapatalk
  8. kidturbo

    Twins with Twins, Anyone?

    Constant pressure spring clamps. Use them on first build, no issues. Boots is another subject. Biggest issue is no flexable material to bridge the gap can withstand a sustained operating temperature above 275 F. Alum tube and v-band first choice, doesn't do well with being stretched repeatedly...
  9. kidturbo

    Twins with Twins, Anyone?

    If vibrant didn't cnc their name into the clamps, I'd be more inclined to use them. However I have video of one exploding at only 50psi on my buddies boat couple years back. So no warm and fuzzy feeling about using those clamps. But I see them used in much higher boost situations all the time...
  10. kidturbo

    Twins with Twins, Anyone?

    If you find a pic please post it. The only examples I found were just regular boots and clamps. But I get the principle to remove stress off the rubber boot. Sent from my SAMSUNG-SM-G890A using Tapatalk
  11. kidturbo

    Twins with Twins, Anyone?

    Yep, up pipes at the manifold Vband. Port 1-2 / Stbd 1-2. It come default set for 2egt and 2cht probes since piston powdered aircraft typically monitor head temp also. But you can rename the inputs what ever ya want. Ch1-4 ect.. 2600F range. Has canbus lines for their custom data logger also...
  12. kidturbo

    Twins with Twins, Anyone?

    EGT gauge arrived today. Pretty cool little $300 experimental aircraft unit that does scalable 4ch, recall, and alarm trigger output. Think I'll hook that wire to the horn relay... Sent from my SAMSUNG-SM-G890A using Tapatalk
  13. kidturbo

    Twins with Twins, Anyone?

    Lift pumps are mounted. Now to plumb everything together. Sent from my SAMSUNG-SM-G890A using Tapatalk
  14. kidturbo

    LML Twins and Opinions

    Super glad to hear things ironing out as expected, and all is right in the Duramax universe again. Now back to Titties & Beer..
  15. kidturbo

    LML Twins and Opinions

    I waited 5 months to get my engines on their dyno after dropping one off. Two guys had time booked ahead of me, money wasn't the issue. I tried that angle.. Looking back, would do it again because the knowledge gained was worth the wait. Didn't overcharge me, probably lost money due to my...
  16. kidturbo

    Twins with Twins, Anyone?

    Ok on the PC and looked those up TDI dampers. Seems VW had an issue with cyl #2 cracking the line. Cummins uses same type clamp to support several of the lines, one laying in my ashtray from last injector swap.. The ones I purchase from MSC are a two bolt plastic that fits snug around the line.
  17. kidturbo

    Twins with Twins, Anyone?

    One bolted to head seemed to tighten it up a bunch. Issue is clearance under that Banks intake. It's pretty tight under there. Sent from my SAMSUNG-SM-G890A using Tapatalk
  18. kidturbo

    Twins with Twins, Anyone?

    Also upon Mark's recommendation, adding a vibration damper clamp on the crossover line so that it won't break and cause excessive engine compartment heat issues. lol Also promised Nick I would put his filter assembly up front and center with his name on it. Guess this counts.. Sent from my...
  19. kidturbo

    Twins with Twins, Anyone?

    Working on the fuel system today. Decided to clean up the frayed return line ends. Little piece of heat shrink goes a long ways. Sent from my SAMSUNG-SM-G890A using Tapatalk
  20. kidturbo

    LML Twins and Opinions

    X2.. I'm about as specialized as ya get, truly one on one customer relationships. But then again, only have half dozen customers, answer about half their calls and emails.. :spit: Seriously, Frogman your dealing with one of most respected diesel performance shops in the country. Have faith...
Top Bottom