Search results

Search the forum Search Articles
  1. durallymax

    Found a Motor, anything I should look for

    so I should offer this guy $1,500. To me it doesnt matter what the issue is as long as the heads and block themselves are still salvaged able. The whole motor will be rebuilt and machined back to specs as well as getting a very stount bottom end.
  2. durallymax

    Found a Motor, anything I should look for

    what price do you think is a fair price?? I guess I really dont know what they go for. Now that I think of it, diesel power (the member not the mag) was selling LBZs with low hours for $3,800 so the price on this LB7 sounds a little high. There is an LLY for sale not far from here for...
  3. durallymax

    Found a Motor, anything I should look for

    Well the other day one of my buddies said there was an 03 duramax motor for sale on craigslist. So i checked it out and after some thinking, i decided i might as well just buy this motor, and slowly build it for pulling, so when the day comes that it is finished I can swap it in, and still have...
  4. durallymax

    45,000lbs.

    Yes it is wet alfalfa 32 in all. Sometimes 34 depends on the length.
  5. durallymax

    512hp 1085lb-ft

    Sorry guys I forgot about the air dog FP150 and draw straw. i always forget about that thing. Rail PSI on the 512hp tune was around 18,000 which I was real happy with. I will check out that table this evening.
  6. durallymax

    512hp 1085lb-ft

    Well I was able to run my bigger tunes today after a lot of work, I finally just went back to my other laptop with V7.4 on it and was able to throw in the pulling tune. I then looked the tune and saw how ridiculous the pusle width was so I cut it back quite a bit and added some more timing...
  7. durallymax

    Made it to the dyno

    well again having EFI issues so no big tune again just my DD tune which I am really starting to like. 13 seconds quuarter miles 450RWHP, 16mpg. I think I will work on cleaning it up a abit and working on the defueling. but anyways as for the dyno party. It wasnt laoding the trucks hardly...
  8. durallymax

    13.69 First Timer

    It was fun to see the look on the 350Z drivers face when my truck shut down before 1000' and I still beat him. A Bunch of ricers I go to school with didnt believe my truck could beat a 350Z non of them believed me when I told them. Racing the camaro was the funnest. Just being able to go up...
  9. durallymax

    13.69 First Timer

    No codes were thrown and It would consistently give me the throttle back in 3-5 seconds. Im thinking it has something to do with rail pressure. I do have an Air Dog 150. Thanks McRat, I do have the limp mode disabled in my pulling tune, but due to my EFI Live issues I couldnt load it. I will...
  10. durallymax

    13.69 First Timer

    havent figured that out, was hoping somebody had some answers for me. It goes into engine protection mode, same as valet mode. Cant go over 2000RPM. I cant figure out why and couldnt modify my tune or log data to figure it out due to the fact that I couldnt get my firmware to update
  11. durallymax

    13.69 First Timer

    Thanks kat. I dont plan on doing much drag racing. The strip is an hour and a half away and the truck will be built more for pulling but I wouldnt mind making more passes. And now I want to since my EFI Live is working correctly so I can dial in the tune.
  12. durallymax

    13.69 First Timer

    Well I made it to great lakes dragway today to do some 1/4 times. It was my first time ever running the 1/4 mile so I really didnt know what to expect. My first run I was up against a Kia Rio. I didnt get the truck spooled up, slept on the line and the engine shutdown before 1,000'. I...
  13. durallymax

    New Custom Crossmember for Alli

    Well I noticed today while loding my truck on the trailer that my crossmember DOES rub. And the deep pan sits a touch lower than the member maybe the same height I cant really tell, its just my miscalibrated eyeball. I did notice that while loading the pan misses and the crossmember is what...
  14. durallymax

    Runaway Diesel Video:

    ouch, this is how new safety features are invented. The air shutoff is one o fthe best features next to the roll cage. Ill never forget when I was a kid and was at the Tomah Super Nationals pull. A tractor rolled and crushed the driver. tons of fans rushed out the flip it back over. we...
  15. durallymax

    New Custom Crossmember for Alli

    without casper being the guinea pig a lot of these parts may have never come to the market place. Thanks Pat. And thanks for a board that is full of only competition folks, and a few that are interested in starting competing. And of course there will always be bad melons but what do you...
  16. durallymax

    New Custom Crossmember for Alli

    primarily, i think this is all that it is. Well high performance, a little joking and the TTS guys bitching. You dont see people on here asking which exhaust to run or which intake to run. Its always which rods, or which turbo, big, bigger or biggest.
  17. durallymax

    DIY CP3 parts

    Good for you. I think you made the right decision to take a break for awhile. Most people dont and it bites them in the end. Hope all goes well. Keep your stick on the ice.
  18. durallymax

    New Custom Crossmember for Alli

    Hmm intersting spin on the thread since I last looked. The best thing about Mike Is that he never sells you anything unless you ask. Call the guy once and start talking to him about your trans problems. Not once will he reccomend you buy something from him or even buy something at all. he...
  19. durallymax

    hdiesel dot com dyno day

    big differece
  20. durallymax

    LBZ DSP5 switch

    It is for LS1 cECMs which the LB7 has. It allows instant tuning. Lets say I add a degree of timing, the secnd I push enter the motor has a degree of timing, no flasing, just instant on the fly tuning. The price has really gone up though. I think its close to a grand. But Ill be getting one if...
Top Bottom