Search results
-
Leaky trans. HELP NEEDED
Well guys, I am out of options. :angry5: I replaced the front seal, pump o-ring, two copper washers, all 10 rubber washers for the pump, and the two large gaskets and I still got the leak. I made sure I used plenty of lube when installing the o-rings, used a press on the seal for even...- toloud4u18
- Post #21
- Forum: Mike L's Trans Talk
-
Leaky trans. HELP NEEDED
When pressing in the seal, does it sit flush with the pump housing, or slightly recessed into the housing? Kind of a dumb question, but the seal I put in with a wood block and hammer sits flush, but on 1 side there is a very slight dip. I am wondering if it didn't get pressed all the way in. I...- toloud4u18
- Post #19
- Forum: Mike L's Trans Talk
-
Leaky trans. HELP NEEDED
Yeah that's true. I got it all apart and did not see anything torn or cut, so I ordered a new seal, o-ring, rubber and copper washers, and gaskets. Should be in tomorrow, then hopefully this will take care of the leak- toloud4u18
- Post #18
- Forum: Mike L's Trans Talk
-
Leaky trans. HELP NEEDED
I didn't notice any vibrations, other than the re-learn process when shifting was extremely harsh. That went away after the relearn though. It's hard to say about the seal, because when the converter was pulled it puked fluid all over. I pulled it as fast as I could, but it still spilled.- toloud4u18
- Post #16
- Forum: Mike L's Trans Talk
-
Leaky trans. HELP NEEDED
Pulled the trans today, the seal doesn't look bad. I didn't find any tears, nicks, or dents in it at all. The bolts were all tight, and it did not appear to be leaking from them. After speaking with the grandmaster, the seal for the pump is kinda where I'm leaning. It's hard to see any...- toloud4u18
- Post #14
- Forum: Mike L's Trans Talk
-
Leaky trans. HELP NEEDED
Yes it was. I removed it to install the transgo shift kit if I remember correctly. Actually it was for the shim from the Gmax kit- toloud4u18
- Post #13
- Forum: Mike L's Trans Talk
-
Leaky trans. HELP NEEDED
Were they loose, or just not sealing right? Did you just use rtv and put them back in or what? Just want to get my ducks in a row...- toloud4u18
- Post #11
- Forum: Mike L's Trans Talk
-
Leaky trans. HELP NEEDED
I'm thinkin that it's gonna need to be pulled out. I pulled both inspection covers and cleaned the housing out, dried it out and took it for a half hour drive. There was a trail of fluid from the weep hole in the bellhousing. What else can/should I check when I pull this thing out? Replace the...- toloud4u18
- Post #9
- Forum: Mike L's Trans Talk
-
Leaky trans. HELP NEEDED
I just went and checked again, definitely trans fluid along the area between trans and engine. What are the possibilities for this leak? Front seal, lower bellhousing bolts inside trans, anything else you guys can think of? I just want to know my options if I pull this thing again.- toloud4u18
- Post #7
- Forum: Mike L's Trans Talk
-
Leaky trans. HELP NEEDED
nothing on the side on the motor wet at all, the fluid is coming from between the bellhousing and the engine.- toloud4u18
- Post #6
- Forum: Mike L's Trans Talk
-
Leaky trans. HELP NEEDED
Yeah pretty sure its trans. Pink/red in color, and on the inspection cover in the pic you can see pink I took another pic after driving around for 10 min, fluid at 135 at the top of cold hatch mark.- toloud4u18
- Post #4
- Forum: Mike L's Trans Talk
-
Leaky trans. HELP NEEDED
I did my own Gmax5 kit with Precision ML tc roughly 3000 miles ago. After the install I didn't see any leaks at all under the truck. Now this morning i see 5-8 drops between the bellhousing and trans as well as on the ground. I wiped off the fluid and started up, let the truck idle and...- toloud4u18
- Thread
- Replies: 24
- Forum: Mike L's Trans Talk