Search
Search titles only
By:
Search titles only
By:
Home
How To
Tech
Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
New showcase items
New showcase comments
Members
Current visitors
New profile posts
Search profile posts
Showcase
New items
New comments
Latest reviews
Search showcase
Tools
ET Calculator
Members
Log in
Register
Search
Search titles only
By:
Search titles only
By:
Current visitors
New profile posts
Search profile posts
Menu
Install the app
Install
ZeroGravity58's latest activity
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
ZeroGravity58
reacted to
johnmyster's post
in the thread
Looking for Allison build/install options near Virginia.
with
Like
.
As a follow up, two camping trips and about 1000 miles in, I'm happy with the trans. No converter slip, solid shifts, and mostly the...
Monday at 4:30 PM
ZeroGravity58
replied to the thread
Valve lash
.
This is how I always set lash on solid rollers. I set the in intake when the exhaust is open and vis versa. Just a habit I got into when...
Saturday at 3:48 PM
ZeroGravity58
replied to the thread
Valve lash
.
The pushrods arnt bent I checked and rolled all the pass side on a table. The tip that rides on lifter looks fine, some of the cups on...
May 10, 2024
ZeroGravity58
replied to the thread
Valve lash
.
Hopefully that's the case, If everything looks good a may throw a set of manton 7/16 pushrods in it for piece of mind
May 8, 2024
ZeroGravity58
replied to the thread
Valve lash
.
I'm gonna borrow a bite scope and check the cam. That's the thing everything was tight. I checked torque on everything before pulling it...
May 7, 2024
ZeroGravity58
replied to the thread
Valve lash
.
It has wagler pushrods. It has no metal in the oil and no wires sounds but the tap from the lash being wrong. I dont see how it would be...
May 6, 2024
ZeroGravity58
posted the thread
Valve lash
in
Duramax Engine Building
.
Built my motor last year. Have put roughly 2k miles on it. A couple months ago I developed a slight valve tick, not to noticable cold...
May 5, 2024
ZeroGravity58
replied to the thread
S300 Kit LMM
.
Smeding doesn't have the best reputation so be prepared. It is a direct drop in I test fitted one I had one of these that needed to be...
May 4, 2024
ZeroGravity58
replied to the thread
Lly/lb7 rebuild
.
If your gonna build it use the crank and pistons, throw a set of the Callie's rods in. They are really hard to bet at 1100
May 4, 2024
ZeroGravity58
replied to the thread
LML GPCM delete?
.
I've done it on a lmm. Loop the canbus wires back together. It will still throw a soft code and the glow plug light will stay on
Apr 26, 2024
ZeroGravity58
replied to the thread
Looking for Allison build/install options near Virginia.
.
George will take care of you, you won't have any problems
Apr 9, 2024
ZeroGravity58
replied to the thread
Looking for Allison build/install options near Virginia.
.
Who did you settle on? George does build a stock plus build, I can tell you it is stout. I have it in my LBZ and I beat the piss out of...
Apr 6, 2024
ZeroGravity58
replied to the thread
Built motor oil
.
Maybe I'll look into swapping oil coolers. It would be a lot easier on the stand 😂. I'm taking temps precooler from the top of the oil...
Apr 4, 2024
ZeroGravity58
replied to the thread
Built motor oil
.
It is, I shoulda went with a lp5 cooler or maybe it would be different if I used a Garrett based charger that is water cooled. I was...
Apr 4, 2024
ZeroGravity58
replied to the thread
Built motor oil
.
That's what I was unsure of, go to thicker oil or thinner oil. I think the oil temp is a combination of things. I ran a stock lbz oil...
Apr 3, 2024
Top
Bottom