What's your fastest.....
- Thread starter Chevy1925
- Start date
I have a 2 year old so I'd say at least 2 days!!!
:thumb:If he doesn't help I'd say 3-5 hours for your first one if you clean out the housing.
Yellowcheevy
concidering we dont you your mechanical skills and tool set, very hard to judge a time.
i can pull the back half of a case off without pulling the t-case but i bent up a set of snap ring pliers to get to the top snap ring and get the cover off.
you will need to pull the t-case to see the snap ring im talking about. might be able to drop the trans crossmember and lower the back of the trans/t-case enough to get a set of reg pliers in there but ive not done that in years and the last one i did was my truck which is lifted and had the t-bar drop bracket on it.
i take that back, if you dad has an ultimate set of tools in his van, should be able to do it in 2 hours
i can pull the back half of a case off without pulling the t-case but i bent up a set of snap ring pliers to get to the top snap ring and get the cover off.
you will need to pull the t-case to see the snap ring im talking about. might be able to drop the trans crossmember and lower the back of the trans/t-case enough to get a set of reg pliers in there but ive not done that in years and the last one i did was my truck which is lifted and had the t-bar drop bracket on it.
i take that back, if you dad has an ultimate set of tools in his van, should be able to do it in 2 hours
I have a 2 year old so I'd say at least 2 days!!!
If he doesn't help I'd say 3-5 hours for your first one if you clean out the housing.
Yellowcheevy
10-4 thank you!
Mechanic skills are pretty good. Put a 350 in a '74 CJ5 I had and when I put the SM465/NP205 in I had the cut the Jeep in half and stretch it a foot to get it in, lol. Also put a complete 3/4 Dodge running gear under a '88 Toyota extended cab pickup. Axles, motor, tranny everything. I'm not worried at all about the the transfer case, I want to take it out anyway so I can clean it good. I just was wondering what kinda time frame I should expect. I will start on it on a Friday after work and finish it on a Saturday, with him helping, lol. Thank you for your response.
Took me about 4 hours to do an egr bloker plate on a LMM.... That's a record right?
I couldn't pry the sumbitch apart....
I couldn't pry the sumbitch apart....
But you also must own a pair of Vans for that James :hug: sorry I just couldn't help myself.
But you also must own a pair of Vans for that James :hug: sorry I just couldn't help myself.
i dont think spicoli wore vans back then :roflmao:
You got to mine in about 3 mins. I fuc**d with it for a good hour before you came by. Something about having catchers gloves for hands and not being able to turn a wrench in that tight of a space
I did pull off a wheel bearing swap on the side of I-15 in about 25 mins. Not too shabby for having to unpack toolbags and run up that damn factory jack for 10 mins just to reach the control arm:rofl:
Engine on stand through grille in 3 hours from turning the key off.. Usually 4hours to pull and have it on a stand..
Dustin wade and I pulled broke engine swapped accessories, then installed new engine in 11-12hours from key off to starting. With some BS in there
Dustin wade and I pulled broke engine swapped accessories, then installed new engine in 11-12hours from key off to starting. With some BS in there
Sorry, I'm not a prima donna that videos all the work I do...video or it didnt happen :roflmao:
oke: :angel:
Sorry, I'm not a prima donna that videos all the work I do...
I can smell the jealousness through the Internet lmao
Im going to install my egr blocker plate on my lly tomorrow.. Hopefully it wont take me nearly this long!!
I think mine took ~45 minutes as I put the plate on the wrong side of the gasket initially.
Corey
