Turbo pedestal porting

[DBUSHLB7]

Here's a few pics of the pedistal Russ did for me. Can't say enough good things about Russ and Scott both. Scott was kind enough to allow Russ to port his BD unit and ship it out to ATS during my motor build. We did an exchange kind of deal. ATS shipped Russ my BD once it was removed. You can clearly see from the first pic just how much casting is able to be removed to match the gasket.

 

[hondarider552]

I thought I was the only one who put turbo stuff on the same table as dinner LOL

 

[yellowchevy]

I thought I was the only one who put turbo stuff on the same table as dinner LOL

Doesn't everybody??
It makes the perfect display area though

Yellowchevy

 

[Ne-max]

How bad are the HTT pedestals?

 

[yellowchevy]

How bad are the HTT pedestals?

I don't know, never messed with one. I would assume they're the same as the BD pedestals but I'd have to see one first hand to know for sure.

Yellowchevy

 

[MAXX IT OUT]

Has anyone ported stock exhaust manifold?

 

[yellowchevy]

Has anyone ported stock exhaust manifold?

That's my next project
I've been wanting to do that for awhile. I think there's good gains to be made porting/polishing stock manifolds & tow flow up pipes, using an LML driver side manifol obviously.
I've had an LML on the shelf for awhile.

Hopefully I'll get a chance this or next month to do so.

Yellowchevy

 

[ryan415]

Has anyone ported stock exhaust manifold?

Haha, I'm actually doing a set of manifolds I got off a lml motor I replaced. They were just sitting in my tool box and I figured what the heck. I started one last week, just don't have a lot of free time rite now lol

 

[yellowchevy]

Haha, I'm actually doing a set of manifolds I got off a lml motor I replaced. They were just sitting in my tool box and I figured what the heck. I started one last week, just don't have a lot of free time rite now lol

Awesome, let us know how it goods :woott:.

Yellowchevy

 

[MAXX IT OUT]

let us know how it goes. I hope there is some good gains for a lot lower cost.

 

[ryan415]

Definitely, I'll try and get some pictures tomorrow :thumb:

 

[yellowchevy]

Definitely, I'll try and get some pictures tomorrow :thumb:

Sounds good :thumb:

I've got some ideas to trys :woott:

Yellowchevy

 

[ryan415]

Here's a couple pictures of what I've done so far, which isn't much honestly lol. I need to get some longer carbides to reach inside. But you can see how restricted the stock ports are.

 

[yellowchevy]

Here's a couple pictures of what I've done so far, which isn't much honestly lol. I need to get some longer carbides to reach inside. But you can see how restricted the stock ports are.

Looks good :thumb:

There's definitely room for improvement.
Get some long 6" die grinder bits, but you need to be careful being they will get off balance if you don't have control of it.

Get egg shape or ball end bits so you can go in the port holes to get the whole thing.

Yellowchevy

 

[MAXX IT OUT]

It looks great.:thumb:

 

[baddaddition]

Looks awesome!!! I love getting on here and just checking out what everyone has going on for projects. Its def. An addicts place to be....... 95% of all the small project pictures are taken on someone's dinner table!!!!! In the still frame I can hear everyone's beloved other going "D**N IT Get that thing off the table while we are eating!!!" Or at least that's what mine always says!!! Lmao!!!

Sent from my DROID RAZR HD using Tapatalk 2