Looks like it ripped the lug of the front of the converter,and thats were the fluid is coming from
Good news vs Bad news
- Thread starter duramaxin14
- Start date
Very good possibleity i beilve i am going to go and get a 1057 converter and do a upgraded pump kit. I hope it can handle the abuse of sled pulling and drag racing and the constated heavy foot.
Larry u where the first i called. i promised i would call u. lol Send me some more tunnage because when its fixed its back on.
you need to do a little more than a converter before you start hammering on it some more, you dont want to be at this same point again in a few months do you?
Very good possibleity i beilve i am going to go and get a 1057 converter and do a upgraded pump kit. I hope it can handle the abuse of sled pulling and drag racing and the constated heavy foot.
Why dont you just lay her up and not drive it until your able to afford a full kit. How will a 1057 and Pump help if your clutches are gone which im sure they are? I limped my tranny like 4 times and knew a I needed to get a transmisson. Not to sound rude but STOP TALKING ABOUT you want to do
You just tore a whole in your transmission by prolonging to have it built. "You Gotta Pay to Play"
Last edited:
Why dont you just lay her up and not drive it until your able to afford a full kit. How will a 1057 and Pump help if your clutches are gone which im sure they are? I limped my tranny like 4 times and knew a I needed to get a transmisson. Not to sound rude but STOP TALKING ABOUT you want to do
I understand paint the clucths in this tranny are burnt i am getting a brand new tranny. So i thought a pump kit and 1057 will hold up. Will it??
Duramaxin14 should be a factory GM parts tester... Nothin' we could ever do to our trucks would break 'em. They would come from the factory with billet rods and stage 5 trannys.
14 if you continue to hammer the truck like you have for the past few months and enjoy it... OVERBUILD the trans. Mike L 4 and a converter and be done. Can't think of much worse than seeing a truck sit that is enjoyed so much!
Well... perhaps divorce and a DUI... but not much else is worse.
14 if you continue to hammer the truck like you have for the past few months and enjoy it... OVERBUILD the trans. Mike L 4 and a converter and be done. Can't think of much worse than seeing a truck sit that is enjoyed so much!
Well... perhaps divorce and a DUI... but not much else is worse.
Duramaxin14 should be a factory GM parts tester... Nothin' we could ever do to our trucks would break 'em. They would come from the factory with billet rods and stage 5 trannys.
14 if you continue to hammer the truck like you have for the past few months and enjoy it... OVERBUILD the trans. Mike L 4 and a converter and be done. Can't think of much worse than seeing a truck sit that is enjoyed so much!
Well... perhaps divorce and a DUI... but not much else is worse.
If i was a gm parts man they wouldnt go off the lot unless they have dyno proven a thousand hp.
umm well ......................................
wow ............................................
well kurt im donating my shirt i had made to u..
100% jack ass... on the front and
HELP ME I CAINT SPELL ON THE BACK............
that sucks man but it shouldnt leak from there i dont think..
im not 100% but hey man find the piece that broke off a lil jb weld and ull be good as new and its only a little scratch i bet some bondo would do a even better job.. just get the high temp stuff..
wow ............................................
well kurt im donating my shirt i had made to u..
100% jack ass... on the front and
HELP ME I CAINT SPELL ON THE BACK............
that sucks man but it shouldnt leak from there i dont think..
im not 100% but hey man find the piece that broke off a lil jb weld and ull be good as new and its only a little scratch i bet some bondo would do a even better job.. just get the high temp stuff..
I already fixed the problem i went down to the local hardware store bought a 5 gallon bucket of liquid weld and put it over the whole. U never knew there was a hole there man. Then take a sander and sand it down.
lol i was going to suggest jb weld ...but now you beat me to it. congrats on the breakage and the fix-it.
Capt
on the breakage and the fix-it.Capt