Forged or Cast pistons

Ron2145

Ron2145

Member
May 6, 2016
46
1
8
Whitefish, MT
My goal is a long term reliable build, it’s my understanding with current 475/stock roughly 800 hp is the max. I do tow with the truck so I figure to keep my current air, I have talked to Will Haase about rebuilding the turbos, although that number may change a little now that I know metal went through them. I’m figuring on going to 100% overs.

I talked to Evan at DHD and Wagler last year. He is far away but I haven’t found a machine shop close. There may be one in Spokane. I’m fairly handy, I did the head gaskets and studs myself a few years ago but I haven’t built an entire engine yet. I can’t decide whether I want to tackle it myself.

I’m not real knowledgeable about what parts I should use if I do it myself.

Thank you everyone for your input!


Sent from my iPhone using Tapatalk Pro
 
gmduramax

gmduramax

Shits broke
Jun 12, 2008
4,072
248
63
Nor cal
Ron2145 said:
My goal is a long term reliable build, it’s my understanding with current 475/stock roughly 800 hp is the max. I do tow with the truck so I figure to keep my current air, I have talked to Will Haase about rebuilding the turbos, although that number may change a little now that I know metal went through them. I’m figuring on going to 100% overs.

I talked to Evan at DHD and Wagler last year. He is far away but I haven’t found a machine shop close. There may be one in Spokane. I’m fairly handy, I did the head gaskets and studs myself a few years ago but I haven’t built an entire engine yet. I can’t decide whether I want to tackle it myself.

I’m not real knowledgeable about what parts I should use if I do it myself.

Thank you everyone for your input!


Sent from my iPhone using Tapatalk Pro
Click to expand...

You’re going to want at least 200% injectors
 
gmduramax

gmduramax

Shits broke
Jun 12, 2008
4,072
248
63
Nor cal
Ron2145 said:
I had wondered about going bigger, I was told 100 was enough. My understanding is with bigger you have a shorter pulse so it should burn a little cooler


Sent from my iPhone using Tapatalk Pro
Click to expand...
100’s are enough for 500hp. You want to keep pulse short so the fuel stays inside the bowl.
 
  • Like
Reactions: Ron2145
Chevy1925

Chevy1925

don't know sh!t about IFS
Staff member
Oct 21, 2009
21,680
5,828
113
Phoenix Az
Ron2145 said:
Is it feasible to build a reliable engine at that hp?


Sent from my iPhone using Tapatalk Pro
Click to expand...
800?? absolutely. fingers pistons, choice of rods, narrow rod journal crank and its good to go. if you dont mind taking a little risk to save some cash, callies durastar crank or a new stock crank can be supplimented.
 
  • Like
Reactions: Bdsankey and Ron2145
LBZ

LBZ

Super Moderator
Staff member
Jul 2, 2007
9,903
149
63
46
B.C.
Bdsankey said:
Let me put it this way, with some new parts that have come to market recently building a motor has become actually quite affordable compared to just a few years ago.
Click to expand...
Depends which side of the border you are on though lol. It’s still ridiculous with exchange rate up here and duty and shipping.
 
  • Like
Reactions: Ron2145
Ron2145

Ron2145

Member
May 6, 2016
46
1
8
Whitefish, MT
Chevy1925 said:
800?? absolutely. fingers pistons, choice of rods, narrow rod journal crank and its good to go. if you dont mind taking a little risk to save some cash, callies durastar crank or a new stock crank can be supplimented.
Click to expand...

What’s your thoughts on the AF cams? Worth doing?


Sent from my iPhone using Tapatalk Pro
 
Bdsankey

Bdsankey

Vendor
Vendor/Sponsor
Feb 1, 2018
4,165
1,274
113
Larsen, Wisconsin
Ron2145 said:
What’s your thoughts on the AF cams? Worth doing?


Sent from my iPhone using Tapatalk Pro
Click to expand...
I like AF cams on brand new cranks but as James said the biggest "sure fire" fix is a NRJ crank. I personally run stock cranks in my engines because I'm too cheap to buy a billet crank and have the time to fix it should I have a problem.
 
  • Like
Reactions: Ron2145
1FastBrick

1FastBrick

Well-known member
Dec 1, 2016
2,541
1,069
113
Junkyard
Bdsankey said:
There are a few. Callies, Winberg, and the SoCal private label are the most common. I don't recall who SoCal pays to have make theirs. The SoCal, from what I've read, is the narrowest.
Click to expand...
Ok, I wasn't sure. I think So Cal's is the only one I have seen. But I believe they are custom made billets by one of the big name crank manufactures here.
 
Chevy1925

Chevy1925

don't know sh!t about IFS
Staff member
Oct 21, 2009
21,680
5,828
113
Phoenix Az
i put a Callies NRJ in the old truck but the socal one is much narrower. At the time, it was 1500 bucks more for the socal crank over the callies. the callies was 3600 shipped to my door. im sure the prices are not that nice anymore...
 
1FastBrick

1FastBrick

Well-known member
Dec 1, 2016
2,541
1,069
113
Junkyard
Chevy1925 said:
i put a Callies NRJ in the old truck but the socal one is much narrower. At the time, it was 1500 bucks more for the socal crank over the callies. the callies was 3600 shipped to my door. im sure the prices are not that nice anymore...
Click to expand...
I am sure....
 
You must log in or register to reply here.
Top Bottom